Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Model 96 cabinet veneer
#11

The veneer in question looks like French walnut, but I think that the first piece looks light because of sun exposure. If these are off the sides of the cabinet, if it was like mine they are plywood panels that were slid into channels between the front and rear stiles or legs of the cabinet, and can slid out of the channels once the cabinet top is taken off. My model 96 was stored in a damp basement so the side panels were coming apart, so I just used some 1/4' plywood, they were also shaded dark so the species of veneer didn't matter, one side had walnut veneer originally, but I think the other may have been maple or poplar.
Regards
Arran


Messages In This Thread
Model 96 cabinet veneer - by TGLager - 10-23-2024, 04:48 PM
RE: Model 96 cabinet veneer - by Arran - 10-23-2024, 11:08 PM
RE: Model 96 cabinet veneer - by klondike98 - 11-04-2024, 12:59 AM
RE: Model 96 cabinet veneer - by TGLager - 11-09-2024, 04:08 PM
RE: Model 96 cabinet veneer - by RodB - 11-10-2024, 10:36 AM
RE: Model 96 cabinet veneer - by TGLager - 11-10-2024, 02:40 PM
RE: Model 96 cabinet veneer - by RodB - 11-10-2024, 07:01 PM
RE: Model 96 cabinet veneer - by TGLager - 11-10-2024, 11:02 PM
RE: Model 96 cabinet veneer - by madsowry - 11-12-2024, 09:58 PM
RE: Model 96 cabinet veneer - by TGLager - 11-13-2024, 09:19 PM
RE: Model 96 cabinet veneer - by Arran - 11-16-2024, 03:25 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
HiFi (Chifi) tube amp build - but my own design.
Tim, nice write up and thanks for sharing !! Sincerely Richardradiorich — 02:47 AM
HiFi (Chifi) tube amp build - but my own design.
Well, this was a real "Hum-Dinger" :lol: ! This will be kinda long, but hopefully it will help others having t...TV MAN — 01:55 AM
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM

[-]
Who's Online
There are currently no members online.

>