1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 1 Vote(s) - 4 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
cap polarity
murf
Senior Member
****
Posts: 668
Threads: 144
Joined: Jun 2011
City: Elko,MN.
#3

07-14-2012, 01:43 PM
If I could figure out how to post a picture,I would have done that.
The mouser pn is 594-2222-138-21229
Mfg pn is mal213821229e3.
Looked at both and could not find anything that states polarity.
Thanks for the help.
murf
Find
« Next Oldest | Next Newest »


Messages In This Thread
cap polarity - by murf - 07-14-2012, 12:46 PM
RE: cap polarity - by morzh - 07-14-2012, 01:12 PM
RE: cap polarity - by murf - 07-14-2012, 01:43 PM
RE: cap polarity - by Bob Andersen - 07-14-2012, 06:11 PM
RE: cap polarity - by murf - 07-14-2012, 07:23 PM
RE: cap polarity - by Ron Ramirez - 07-14-2012, 08:02 PM
RE: cap polarity - by morzh - 07-15-2012, 11:34 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM

[-]
Who's Online
There are currently 4563 online users. [Complete List]
» 1 Member(s) | 4562 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration