1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 38-62 restoration
Arran
Phorum Expert
*****
Posts: 4,703
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
#2

02-21-2013, 07:14 PM
By the tensioning ring do you mean the "C" clip that fits in a groove on the control's shaft? I would try removing one from a scrapped control and see if that fits, you need a sharp flat bladed screwdriver to push them off the shaft, sometimes you need to pry the ends open with a jewelers screwdriver or something first.
Regards
Arran
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 38-62 restoration - by Bob Andersen - 02-21-2013, 06:25 PM
RE: Philco 38-62 restoration - by Arran - 02-21-2013, 07:14 PM
RE: Philco 38-62 restoration - by klondike98 - 02-21-2013, 09:43 PM
RE: Philco 38-62 restoration - by Arran - 02-21-2013, 10:22 PM
RE: Philco 38-62 restoration - by Bob Andersen - 02-21-2013, 10:57 PM
RE: Philco 38-62 restoration - by Bob Andersen - 02-22-2013, 12:56 AM
RE: Philco 38-62 restoration - by Arran - 02-22-2013, 02:36 AM
RE: Philco 38-62 restoration - by Bob Andersen - 02-22-2013, 05:27 PM
RE: Philco 38-62 restoration - by Bob Andersen - 03-02-2013, 12:39 AM
RE: Philco 38-62 restoration - by Phlogiston - 03-02-2013, 01:14 PM
RE: Philco 38-62 restoration - by morzh - 03-02-2013, 10:32 PM
RE: Philco 38-62 restoration - by Bob Andersen - 03-03-2013, 12:35 AM
RE: Philco 38-62 restoration - by Ron Ramirez - 03-03-2013, 08:58 AM
RE: Philco 38-62 restoration - by morzh - 03-03-2013, 09:52 AM
RE: Philco 38-62 restoration - by codefox1 - 03-03-2013, 12:57 PM
RE: Philco 38-62 restoration - by jerryhawthorne - 03-03-2013, 05:40 PM
RE: Philco 38-62 restoration - by Bob Andersen - 03-03-2013, 05:53 PM
RE: Philco 38-62 restoration - by Tom Hamilton - 03-23-2013, 09:31 PM
RE: Philco 38-62 restoration - by Bob Andersen - 03-24-2013, 12:21 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM
My last cabinet for this year
Hello Dan, That is really beautiful what great looking radio you have ! I have friends who live in Calgary and the wea...radiorich — 01:51 AM

[-]
Who's Online
There are currently 4514 online users. [Complete List]
» 3 Member(s) | 4511 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration