1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 38-62 restoration
Bob Andersen
Phorum Expert
*****
Posts: 797
Threads: 42
Joined: Dec 2008
City: Chicago, IL
#17

03-03-2013, 05:53 PM
Thanks! That TV chassis was by far the nastiest project I've tackled so far. Under the mouse droppings, I found deep corrosion. Almost right through the chassis in areas. That's why I used primer and bondo to fill it in. The set isn't particularly valuable or anything - I just wanted to see if I could do it Icon_smile
(This post was last modified: 03-03-2013, 05:54 PM by Bob Andersen.)
Website Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 38-62 restoration - by Bob Andersen - 02-21-2013, 06:25 PM
RE: Philco 38-62 restoration - by Arran - 02-21-2013, 07:14 PM
RE: Philco 38-62 restoration - by klondike98 - 02-21-2013, 09:43 PM
RE: Philco 38-62 restoration - by Arran - 02-21-2013, 10:22 PM
RE: Philco 38-62 restoration - by Bob Andersen - 02-21-2013, 10:57 PM
RE: Philco 38-62 restoration - by Bob Andersen - 02-22-2013, 12:56 AM
RE: Philco 38-62 restoration - by Arran - 02-22-2013, 02:36 AM
RE: Philco 38-62 restoration - by Bob Andersen - 02-22-2013, 05:27 PM
RE: Philco 38-62 restoration - by Bob Andersen - 03-02-2013, 12:39 AM
RE: Philco 38-62 restoration - by Phlogiston - 03-02-2013, 01:14 PM
RE: Philco 38-62 restoration - by morzh - 03-02-2013, 10:32 PM
RE: Philco 38-62 restoration - by Bob Andersen - 03-03-2013, 12:35 AM
RE: Philco 38-62 restoration - by Ron Ramirez - 03-03-2013, 08:58 AM
RE: Philco 38-62 restoration - by morzh - 03-03-2013, 09:52 AM
RE: Philco 38-62 restoration - by codefox1 - 03-03-2013, 12:57 PM
RE: Philco 38-62 restoration - by jerryhawthorne - 03-03-2013, 05:40 PM
RE: Philco 38-62 restoration - by Bob Andersen - 03-03-2013, 05:53 PM
RE: Philco 38-62 restoration - by Tom Hamilton - 03-23-2013, 09:31 PM
RE: Philco 38-62 restoration - by Bob Andersen - 03-24-2013, 12:21 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
trying to identify this wire type
Thanks to all for the feedback. As Arran said, it is probably an older replacement and yes it has a grid cap so I will ...georgetownjohn — 09:32 PM
trying to identify this wire type
It's possible that the red wire, actually a grid cap lead, is a very old replacement, I can't remember seeing a pre 1939...Arran — 09:18 PM
Gilfillan Brothers Car Radio?
Hi everyone,  Special thanks to Joe Rossi for tracking down this obscure radio and thanks to others who took up the hun...Antipodal — 08:15 PM
trying to identify this wire type
Here's one source for your wire of many. Take care and BE HEALTHY! Gary P.S. Can't get the right color you need? I ...GarySP — 06:40 PM
trying to identify this wire type
...and modern wire of the appropriate gauges and insulation V-rating (300V minimum, usually shown right on the wire) is ...morzh — 05:47 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
I have a question about this radio, is there anyone that has access to this radio that has an intact unmolested speaker ...captainclock1988 — 04:28 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Well what makes me confuse all of those companies is that all three of those companies (Setchell-Carlson, Stromberg-Carl...captainclock1988 — 04:21 PM
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached.  I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration