116X Finish

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

116X Finish

Ron Ramirez
Silent Key

Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana

#20

03-22-2013, 04:46 PM

If it were shellac, acetone would have easily removed it.

And if acetone didn't have any effect on the finish, it sounds like it is the dreaded P-word...polyurethane. Icon_eek

--
Ron Ramirez
Ferdinand IN

Find

« Next Oldest | Next Newest »

Messages In This Thread

116X Finish - by ipwizard - 03-04-2013, 10:45 PM

RE: 116X Finish - by Arran - 03-05-2013, 03:24 AM

RE: 116X Finish - by ipwizard - 03-05-2013, 03:43 PM

RE: 116X Finish - by Ron Ramirez - 03-05-2013, 05:54 PM

RE: 116X Finish - by Phlogiston - 03-05-2013, 06:21 PM

RE: 116X Finish - by Arran - 03-05-2013, 08:03 PM

RE: 116X Finish - by ipwizard - 03-05-2013, 08:14 PM

RE: 116X Finish - by Phlogiston - 03-05-2013, 10:30 PM

RE: 116X Finish - by Ron Ramirez - 03-06-2013, 08:57 AM

RE: 116X Finish - by Phlogiston - 03-06-2013, 11:33 AM

RE: 116X Finish - by Chuck Schwark - 03-06-2013, 04:10 PM

RE: 116X Finish - by Ron Ramirez - 03-07-2013, 05:26 PM

RE: 116X Finish - by Phlogiston - 03-08-2013, 01:42 AM

RE: 116X Finish - by Phlogiston - 03-08-2013, 01:51 AM

RE: 116X Finish - by ipwizard - 03-14-2013, 03:37 PM

RE: 116X Finish - by ipwizard - 03-14-2013, 03:54 PM

RE: 116X Finish - by Phlogiston - 03-14-2013, 04:28 PM

RE: 116X Finish - by Arran - 03-14-2013, 06:47 PM

RE: 116X Finish - by ipwizard - 03-22-2013, 04:29 PM

RE: 116X Finish - by Ron Ramirez - 03-22-2013, 04:46 PM

RE: 116X Finish - by ipwizard - 03-22-2013, 08:25 PM

RE: 116X Finish - by Ron Ramirez - 03-22-2013, 08:38 PM

RE: 116X Finish - by Phlogiston - 03-22-2013, 09:12 PM

RE: 116X Finish - by Arran - 04-01-2013, 02:30 AM

View a Printable Version

Users browsing this thread: 10 Guest(s)

Recent Posts
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM
Model 28L
Hello, I'm restoring a Philco 28L and the output transformer is open. Part number of the transformer is 32-7020. Can...HORSTE — 10:32 AM
Philco 42-1008 conversion kit
I read about a kit to convert the variable speed changer in the Philco 42-1008 into a single speed unit. That would rem...alangard — 09:30 PM

Who's Online

There are currently 6008 online users. [Complete List]
» 1 Member(s) | 6007 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me