1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Restoration/code changes
TonyJSenior
Member
***
Posts: 111
Threads: 27
Joined: Oct 2007
City: Livonia, MI
#1

11-23-2007, 07:28 PM
Started recapping the chassis of a 38-7 table model and noticed a few differences between the console chassis and this one. I have to believe that they are production changes as the console has a resistor/clamp/thermal compensator mentioned in a run change while the table chassis does not. A few of the caps for the tone control were also the same as the print and not the values mentioned in one of the production run changes. Question I have is, typically when you recap/restore a chassis, if the chassis is an earlier run, do you also go through the run changes and change whatever is noted to bring it to the 'latest' production run?
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Restoration/code changes - by TonyJSenior - 11-23-2007, 07:28 PM
[No subject] - by Ron Ramirez - 11-24-2007, 12:17 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
VTVM meter moves when my hand is next to it & not on
Haha! I hope so. It seemed rather lost and forgotten languishing in the frozen Northeast of England.EdHolland — 02:36 PM
VTVM meter moves when my hand is next to it & not on
Ed - it's in the Cayman's enjoying the good life.RodB — 02:14 PM
VTVM meter moves when my hand is next to it & not on
Static electricity - but the other chaps beat me to it again. I've seen this before with analogue meters. I've also ...EdHolland — 01:56 PM
Need to purchase some accessories for restoration of my Old Philco Radio
Hi Paulo, Welcome to the Philco Phorum. I can see why you want to find good reproduction parts. That is a bea...MrFixr55 — 11:10 PM
HiFi (Chifi) tube amp build - but my own design.
Tim, I have some bakelite sockets in my work shop that I can dig up. I believe quite a few are NOS. I will take photo...RodB — 10:03 PM
Philco 610B oscillator wiring
> The cathode as noted is wired directly to the ground side of the heater filament for that tube, not to the #17 and ...Radioroslyn — 08:12 PM
HiFi (Chifi) tube amp build - but my own design.
Tim; I noticed your post a little late, but I would take one of the junk sockets and try to break a chunk out of it wi...Arran — 08:07 PM
Need to purchase some accessories for restoration of my Old Philco Radio
Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM
First Radio restoration
Hi Tubeman, Welcome to the Philco Phorum.  Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM
First Radio restoration
You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM

[-]
Who's Online
There are currently 1519 online users. [Complete List]
» 1 Member(s) | 1518 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration