Canadian 345 Butterfly

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Canadian 345 Butterfly

murf
Senior Member

Posts: 668
Threads: 144
Joined: Jun 2011
City: Elko,MN.

02-21-2014, 09:23 PM

Looks nice.
Alot of work re-stuffing all those caps.
I don't have the patience to go that route.
I see you eliminated that large type 484 cap in the upper right of the picture.
Was that added by someone else in the past?
Anyway, good job.
murf

Find

« Next Oldest | Next Newest »

Messages In This Thread

Canadian 345 Butterfly - by gregb - 02-21-2014, 08:51 PM

RE: Canadian 345 Butterfly - by morzh - 02-21-2014, 08:57 PM

RE: Canadian 345 Butterfly - by murf - 02-21-2014, 09:23 PM

RE: Canadian 345 Butterfly - by morzh - 02-21-2014, 09:28 PM

RE: Canadian 345 Butterfly - by gregb - 02-21-2014, 09:42 PM

RE: Canadian 345 Butterfly - by morzh - 02-21-2014, 09:49 PM

RE: Canadian 345 Butterfly - by Mondial - 02-21-2014, 10:01 PM

RE: Canadian 345 Butterfly - by gregb - 02-21-2014, 10:03 PM

RE: Canadian 345 Butterfly - by klondike98 - 02-21-2014, 10:06 PM

RE: Canadian 345 Butterfly - by gregb - 02-21-2014, 10:09 PM

RE: Canadian 345 Butterfly - by gregb - 02-21-2014, 10:10 PM

RE: Canadian 345 Butterfly - by Mondial - 02-21-2014, 10:32 PM

RE: Canadian 345 Butterfly - by klondike98 - 02-21-2014, 10:42 PM

RE: Canadian 345 Butterfly - by gregb - 02-21-2014, 10:43 PM

RE: Canadian 345 Butterfly - by Arran - 02-21-2014, 10:45 PM

RE: Canadian 345 Butterfly - by klondike98 - 02-21-2014, 10:53 PM

RE: Canadian 345 Butterfly - by gregb - 02-21-2014, 11:01 PM

RE: Canadian 345 Butterfly - by klondike98 - 02-21-2014, 11:07 PM

RE: Canadian 345 Butterfly - by Arran - 02-21-2014, 11:45 PM

RE: Canadian 345 Butterfly - by morzh - 02-21-2014, 11:52 PM

RE: Canadian 345 Butterfly - by gregb - 02-21-2014, 11:55 PM

RE: Canadian 345 Butterfly - by gregb - 02-22-2014, 12:03 AM

RE: Canadian 345 Butterfly - by Arran - 02-22-2014, 12:04 AM

RE: Canadian 345 Butterfly - by morzh - 02-22-2014, 11:53 AM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Samlex heavy-Duty bench supply filter question
Hello Everyone, I have one of my Heavy-duty bench powersuplies made by Samlex it's 13.8 volt dc 20-25 amp supply. What I...radiorich — 11:24 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
It's a Glaser Sears changer which Philco's engineers thought was an upgrade over a VM, but in retrospect I'd prefer the ...jeibner — 10:39 PM
AC/DC Transformer-less Sets
Joseph, Thank you for the confirmation. I knew that there must be more to the Transformer-less AC/DC radios than the ...PeterN — 10:30 PM
AC/DC Transformer-less Sets
Good evening, folks. Power station engineer here! The east coast had pockets of DC-only power well into the twentieth...jrblasde — 10:11 PM
AC/DC Transformer-less Sets
Model 40 does not have a rectifier, so it would be a DC only model. This however does not say anything about using...morzh — 08:01 PM
AC/DC Transformer-less Sets
I was wondering if anyone knows if these AC/DC transformer-less sets were actually used on 110v DC anywhere, and when. ...PeterN — 06:35 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
Given the 1960s vintage, it is likely that the cartridge is ceramic, likely more stable. The changer looks like a Voice...MrFixr55 — 05:03 PM
Jackson 665 j2 schematic request
FIXED!daveone23 — 03:55 PM
Bakelite crack repair - what is best epoxy?
Thanks everyone. I appreciate you sharing your experience and looks like I'll work with the 24 hr two part clear epoxy....de371 — 10:25 PM
Jackson 665 j2 schematic request
Without a schematic its going to be hard tracing the wire wound spool resistors.daveone23 — 05:21 PM

Who's Online

There are currently 4935 online users. [Complete List]
» 4 Member(s) | 4931 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me