Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Canadian 345 Butterfly
#5

The after is exactly as is should be, the missing caps were previous repairs that I removed and replaced with the proper part number restuffed cap. Radios that I plan on keeping I will go the extra mile to make it as perfect as I can. Some might think its overkill and they may be right but this is the part of the hobby that I enjoy the most.
Like I said in another thread I would love to do this to a 38-690.
Thanks Morzh for the kind words.

Gregb


Messages In This Thread
Canadian 345 Butterfly - by gregb - 02-21-2014, 09:51 PM
RE: Canadian 345 Butterfly - by morzh - 02-21-2014, 09:57 PM
RE: Canadian 345 Butterfly - by murf - 02-21-2014, 10:23 PM
RE: Canadian 345 Butterfly - by morzh - 02-21-2014, 10:28 PM
RE: Canadian 345 Butterfly - by gregb - 02-21-2014, 10:42 PM
RE: Canadian 345 Butterfly - by morzh - 02-21-2014, 10:49 PM
RE: Canadian 345 Butterfly - by Mondial - 02-21-2014, 11:01 PM
RE: Canadian 345 Butterfly - by gregb - 02-21-2014, 11:03 PM
RE: Canadian 345 Butterfly - by klondike98 - 02-21-2014, 11:06 PM
RE: Canadian 345 Butterfly - by gregb - 02-21-2014, 11:09 PM
RE: Canadian 345 Butterfly - by gregb - 02-21-2014, 11:10 PM
RE: Canadian 345 Butterfly - by Mondial - 02-21-2014, 11:32 PM
RE: Canadian 345 Butterfly - by klondike98 - 02-21-2014, 11:42 PM
RE: Canadian 345 Butterfly - by gregb - 02-21-2014, 11:43 PM
RE: Canadian 345 Butterfly - by Arran - 02-21-2014, 11:45 PM
RE: Canadian 345 Butterfly - by klondike98 - 02-21-2014, 11:53 PM
RE: Canadian 345 Butterfly - by gregb - 02-22-2014, 12:01 AM
RE: Canadian 345 Butterfly - by klondike98 - 02-22-2014, 12:07 AM
RE: Canadian 345 Butterfly - by Arran - 02-22-2014, 12:45 AM
RE: Canadian 345 Butterfly - by morzh - 02-22-2014, 12:52 AM
RE: Canadian 345 Butterfly - by gregb - 02-22-2014, 12:55 AM
RE: Canadian 345 Butterfly - by gregb - 02-22-2014, 01:03 AM
RE: Canadian 345 Butterfly - by Arran - 02-22-2014, 01:04 AM
RE: Canadian 345 Butterfly - by morzh - 02-22-2014, 12:53 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Usually a wave trap is for keeping IF signals from entering the antenna and from leaving the antenna. You feed an IF sig...RodB — 09:30 PM
Philco 60 Squealing
I just peaked it for the best signal at 600. NULL it for IF frequency, originally it would have been null for 500kh...Chas — 08:05 PM
Philco 60 Squealing
Wavetrap no longer matters.morzh — 05:19 PM
Philco 60 Squealing
Rod, I had checked out your suggestions but did not help. I did solder the ground rivets to the chassis as Chas suggeste...dconant — 04:52 PM
37-690 Bass Choke Replacement
Yeah, I know, Mouser and Digikey don't have "big iron" components. For some reason Philco was messing with the...Radiodial — 04:25 PM
37-690 Bass Choke Replacement
Yes, I just had to deal with that while repairing the 37-604 Philco. Exactly that value choke was gone. And the current ...morzh — 03:52 PM
37-690 Bass Choke Replacement
Ah, now where to find one. I've into this before on smaller sets, I now recall. Hammond makes one that is only rated...Radiodial — 03:27 PM
Philco 38-7 Speaker
Ask the admins to put them together. As for the renaming, while inside the thread, you simply press "New reply&quo...morzh — 02:23 PM
37-690 Bass Choke Replacement
This is the parts catalog. 32-7528 choke is 65H, 10mA, 2,250 Ohm inductance. Find a suitable one.morzh — 02:18 PM
37-690 Bass Choke Replacement
While troubleshooting the no bass amplification issue, I think I found the culprit. The choke #104 is reading 164K ohms....Radiodial — 01:42 PM

[-]
Who's Online
There are currently 1683 online users. [Complete List]
» 1 Member(s) | 1682 Guest(s)
Avatar

>