Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Canadian 345 Butterfly
#10

Mondial, Thank you, I have come to the same conclusion. I have repaired/restored 1000's of radios over the years and was thinking about what the future holds for collectors. They wont know what an original radio chassis looked like. So for now on all my keeper radios get the full meal deal and brought back to as close to original as I can.

Gregb


Messages In This Thread
Canadian 345 Butterfly - by gregb - 02-21-2014, 08:51 PM
RE: Canadian 345 Butterfly - by morzh - 02-21-2014, 08:57 PM
RE: Canadian 345 Butterfly - by murf - 02-21-2014, 09:23 PM
RE: Canadian 345 Butterfly - by morzh - 02-21-2014, 09:28 PM
RE: Canadian 345 Butterfly - by gregb - 02-21-2014, 09:42 PM
RE: Canadian 345 Butterfly - by morzh - 02-21-2014, 09:49 PM
RE: Canadian 345 Butterfly - by Mondial - 02-21-2014, 10:01 PM
RE: Canadian 345 Butterfly - by gregb - 02-21-2014, 10:03 PM
RE: Canadian 345 Butterfly - by klondike98 - 02-21-2014, 10:06 PM
RE: Canadian 345 Butterfly - by gregb - 02-21-2014, 10:09 PM
RE: Canadian 345 Butterfly - by gregb - 02-21-2014, 10:10 PM
RE: Canadian 345 Butterfly - by Mondial - 02-21-2014, 10:32 PM
RE: Canadian 345 Butterfly - by klondike98 - 02-21-2014, 10:42 PM
RE: Canadian 345 Butterfly - by gregb - 02-21-2014, 10:43 PM
RE: Canadian 345 Butterfly - by Arran - 02-21-2014, 10:45 PM
RE: Canadian 345 Butterfly - by klondike98 - 02-21-2014, 10:53 PM
RE: Canadian 345 Butterfly - by gregb - 02-21-2014, 11:01 PM
RE: Canadian 345 Butterfly - by klondike98 - 02-21-2014, 11:07 PM
RE: Canadian 345 Butterfly - by Arran - 02-21-2014, 11:45 PM
RE: Canadian 345 Butterfly - by morzh - 02-21-2014, 11:52 PM
RE: Canadian 345 Butterfly - by gregb - 02-21-2014, 11:55 PM
RE: Canadian 345 Butterfly - by gregb - 02-22-2014, 12:03 AM
RE: Canadian 345 Butterfly - by Arran - 02-22-2014, 12:04 AM
RE: Canadian 345 Butterfly - by morzh - 02-22-2014, 11:53 AM



Users browsing this thread: 6 Guest(s)
[-]
Recent Posts
Samlex heavy-Duty bench supply filter question
Hello Everyone, I have one of my Heavy-duty bench powersuplies made by Samlex it's 13.8 volt dc 20-25 amp supply. What I...radiorich — 11:24 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
It's a Glaser Sears changer which Philco's engineers thought was an upgrade over a VM, but in retrospect I'd prefer the ...jeibner — 10:39 PM
AC/DC Transformer-less Sets
Joseph, Thank you for the confirmation. I knew that there must be more to the Transformer-less AC/DC radios than the ...PeterN — 10:30 PM
AC/DC Transformer-less Sets
Good evening, folks. Power station engineer here! The east coast had pockets of DC-only power well into the twentieth...jrblasde — 10:11 PM
AC/DC Transformer-less Sets
Model 40 does not have a rectifier, so it would be a DC only model. This however does not say anything about using...morzh — 08:01 PM
AC/DC Transformer-less Sets
I was wondering if anyone knows if these AC/DC transformer-less sets were actually used on 110v DC anywhere, and when. ...PeterN — 06:35 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
Given the 1960s vintage, it is likely that the cartridge is ceramic, likely more stable. The changer looks like a Voice...MrFixr55 — 05:03 PM
Jackson 665 j2 schematic request
FIXED!daveone23 — 03:55 PM
Bakelite crack repair - what is best epoxy?
Thanks everyone. I appreciate you sharing your experience and looks like I'll work with the 24 hr two part clear epoxy....de371 — 10:25 PM
Jackson 665 j2 schematic request
Without a schematic its going to be hard tracing the wire wound spool resistors.daveone23 — 05:21 PM

[-]
Who's Online
There are currently 4404 online users. [Complete List]
» 3 Member(s) | 4401 Guest(s)
AvatarAvatarAvatar

>