I finally finished my 66B

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

I finally finished my 66B

Eric Adams
Phorum Expert

Posts: 825
Threads: 113
Joined: Aug 2012
City: The Villages State, Province, Country: Florida

05-21-2014, 09:01 AM

Thanks guys.
Kirk,
The veneer is from Rockler . It is pressure sensitive. No messing with glue, etc.
I've used it before and have always had great results.

Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org

Website Find

« Next Oldest | Next Newest »

Messages In This Thread

I finally finished my 66B - by Eric Adams - 05-21-2014, 12:19 AM

RE: I finally finished my 66B - by NostalgiaRadioTime - 05-21-2014, 12:43 AM

RE: I finally finished my 66B - by OldRestorer - 05-21-2014, 08:20 AM

RE: I finally finished my 66B - by Eric Adams - 05-21-2014, 09:01 AM

RE: I finally finished my 66B - by morzh - 05-21-2014, 09:32 AM

RE: I finally finished my 66B - by gregb - 05-21-2014, 09:45 AM

RE: I finally finished my 66B - by AI2V - 05-21-2014, 10:32 AM

RE: I finally finished my 66B - by PAradiogeek - 05-21-2014, 11:58 AM

RE: I finally finished my 66B - by Eric Adams - 05-21-2014, 01:25 PM

RE: I finally finished my 66B - by Warren - 05-21-2014, 05:26 PM

RE: I finally finished my 66B - by KCMike - 05-21-2014, 06:12 PM

RE: I finally finished my 66B - by 462ron - 05-21-2014, 07:38 PM

RE: I finally finished my 66B - by Eric Adams - 05-21-2014, 11:09 PM

RE: I finally finished my 66B - by Paul Philco322 - 05-22-2014, 07:07 PM

RE: I finally finished my 66B - by codefox1 - 05-22-2014, 09:08 PM

RE: I finally finished my 66B - by PhilcoJohn - 05-23-2014, 06:26 AM

RE: I finally finished my 66B - by klondike98 - 05-23-2014, 12:13 PM

View a Printable Version

Users browsing this thread: 5 Guest(s)

Recent Posts
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM

Who's Online

There are currently 6858 online users. [Complete List]
» 1 Member(s) | 6857 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me