Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Restoration Cost question
#8

Arran,

If you reread my post, I did not count the power tranny in the initial calc, as I was following yours. I added it in your second scenario where it might be bad.

and, no, I do not see $800 either. But not $120-150 either. This is why I asked about the degree of the resto job. Caps restuffed etc - I say $350 easy. Labour included.

$800 is a bit insane.


Messages In This Thread
Restoration Cost question - by CJK - 08-01-2014, 11:49 AM
RE: Restoration Cost question - by morzh - 08-01-2014, 12:25 PM
RE: Restoration Cost question - by klondike98 - 08-01-2014, 07:43 PM
RE: Restoration Cost question - by morzh - 08-01-2014, 08:12 PM
RE: Restoration Cost question - by Arran - 08-01-2014, 08:34 PM
RE: Restoration Cost question - by morzh - 08-01-2014, 09:39 PM
RE: Restoration Cost question - by Arran - 08-01-2014, 10:36 PM
RE: Restoration Cost question - by morzh - 08-01-2014, 10:59 PM
RE: Restoration Cost question - by Arran - 08-02-2014, 01:02 AM
RE: Restoration Cost question - by GarySP - 08-02-2014, 07:09 AM
RE: Restoration Cost question - by Eric Adams - 08-02-2014, 09:48 AM
RE: Restoration Cost question - by CJK - 08-02-2014, 10:00 AM
RE: Restoration Cost question - by morzh - 08-02-2014, 11:20 AM
RE: Restoration Cost question - by gregb - 08-02-2014, 12:17 PM
RE: Restoration Cost question - by Arran - 08-02-2014, 08:20 PM
RE: Restoration Cost question - by morzh - 08-02-2014, 09:38 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
HiFi (Chifi) tube amp build - but my own design.
Tim, nice write up and thanks for sharing !! Sincerely Richardradiorich — 02:47 AM
HiFi (Chifi) tube amp build - but my own design.
Well, this was a real "Hum-Dinger" :lol: ! This will be kinda long, but hopefully it will help others having t...TV MAN — 01:55 AM
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM

[-]
Who's Online
There are currently 6906 online users. [Complete List]
» 2 Member(s) | 6904 Guest(s)
AvatarAvatar

>