Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

40-180 Cabinet and Buttons
#2

 I think that you may have to strip the top and the control panel, the lacquer on top looks like it's dead and flaking off due to water damage, plus it looks like there is a burn mark, trying to touch up things like that never looks quite right, you may want to strip the shoulder sections on top as well, for similar reasons. It's a common problem with any old console that was left to the clutches of silly housewives who insisted on putting potted plants on top of radio cabinets, or from drinkers and smokers using the radio cabinet as a bar top and or ashtray. Now if you are careful you can strip around the decals to save them, though they are readily available from Radio Daze. To get those panels to match the rest you will have to use a light walnut tone spray, the dye based type, for the base of the cabinet it was either medium walnut or perfect brown, again dye based.  
Regards
Arran


Messages In This Thread
40-180 Cabinet and Buttons - by mgambuzza - 11-02-2014, 09:56 AM
RE: 40-180 Cabinet and Buttons - by Arran - 11-04-2014, 01:40 AM
RE: 40-180 Cabinet and Buttons - by Raleigh - 11-18-2014, 01:04 AM
RE: 40-180 Cabinet and Buttons - by Edisla - 11-21-2014, 09:02 PM
RE: 40-180 Cabinet and Buttons - by klondike98 - 11-21-2014, 11:37 PM
RE: 40-180 Cabinet and Buttons - by Edisla - 11-22-2014, 01:27 AM
RE: 40-180 Cabinet and Buttons - by Edisla - 11-22-2014, 01:32 AM
RE: 40-180 Cabinet and Buttons - by Arran - 11-22-2014, 02:00 AM
RE: 40-180 Cabinet and Buttons - by Edisla - 11-22-2014, 02:31 AM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
Philco 38-7 Oscillation
Will do, thank you.tludka — 10:26 AM
Philco 38-7 Oscillation
As to your oscillation issue I would align the IF transformers. That may solve the problem. You also would want to check...Radioroslyn — 10:22 AM
Philco 38-7 Speaker
Thank you, I will check this out, I do have some shields I can place around the specific tubes. I searched the four que...tludka — 10:18 AM
Philco 38-7 Speaker
Also, check if any wires going to Grid Caps of the tubes that are supposed to be INSIDE of their respective shields (if ...morzh — 09:54 AM
Philco 38-7 Oscillation
Usually in this forum, when we discuss a radio, we do not multiply threads. You already have a thread on this. If you wa...morzh — 09:27 AM
identify very thin wire for replacement on 37-640
You can possibly use a heatshrink tubing. If you decide to replace the wire, anything gauge 24, 300V rated will do (it ...morzh — 09:25 AM
identify very thin wire for replacement on 37-640
Happy Thanksgiving,  I have attche a photo of a very thin wire with black plastic-looking insulation(some of it has com...georgetownjohn — 09:14 AM
Philco 60 Squealing
I got my signal tracer out to see if I could tell at what stage the squeal was coming from. It is present on the plate o...dconant — 09:07 AM
Philco 16B Parts
The 16B's in the tombstone cabinet sport a 10 1/2" spkr vs the older cathedral sets which uses an 8". The p/p ...Radioroslyn — 12:58 AM
Philco 38-7 Oscillation
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 11:16 PM

[-]
Who's Online
There are currently 4880 online users. [Complete List]
» 1 Member(s) | 4879 Guest(s)
Avatar

>