1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Resistor values question
Radioroslyn
Phorum Expert
*****
Posts: 7,296
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#27

03-19-2015, 04:08 PM
Looks like it's 2 o ooo @3oov But some of those postage stamp cap are screwy to decode.
I left my little oarfin Annie decoder ring at work today

So Kirk I'm getting a little peeved will you! YOU HAVEN'T INVITED ME UP TO YOUR NEW PLACE!
I mean I was thinking you could put out your 50 worst chassis and we could knock them out in a few hours
But no invitey no fixy Beside I have something warm and fuzzy for you.
Terry
ps The problem with measuring the 220 ohm resistor is when you set your meter for 200 ohms it can't
measure any thing above 200 ohms. When you set your meter for the next higher range it can measure it.
(This post was last modified: 03-19-2015, 05:20 PM by Radioroslyn.)
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Resistor values question - by OldRestorer - 03-05-2015, 01:29 PM
RE: Resistor values question - by morzh - 03-05-2015, 01:41 PM
RE: Resistor values question - by OldRestorer - 03-05-2015, 02:02 PM
RE: Resistor values question - by Kestas - 03-05-2015, 02:22 PM
RE: Resistor values question - by OldRestorer - 03-05-2015, 03:05 PM
RE: Resistor values question - by sam - 03-05-2015, 03:22 PM
RE: Resistor values question - by morzh - 03-05-2015, 04:25 PM
RE: Resistor values question - by OldRestorer - 03-05-2015, 05:02 PM
RE: Resistor values question - by sam - 03-05-2015, 05:13 PM
RE: Resistor values question - by morzh - 03-05-2015, 05:16 PM
RE: Resistor values question - by OldRestorer - 03-06-2015, 10:39 AM
RE: Resistor values question - by morzh - 03-06-2015, 10:44 AM
RE: Resistor values question - by OldRestorer - 03-06-2015, 10:53 AM
RE: Resistor values question - by OldRestorer - 03-06-2015, 10:58 AM
RE: Resistor values question - by sam - 03-06-2015, 11:10 AM
RE: Resistor values question - by morzh - 03-06-2015, 11:12 AM
RE: Resistor values question - by OldRestorer - 03-06-2015, 01:24 PM
RE: Resistor values question - by Radioroslyn - 03-06-2015, 02:34 PM
RE: Resistor values question - by Radioroslyn - 03-06-2015, 03:09 PM
RE: Resistor values question - by OldRestorer - 03-06-2015, 10:08 PM
RE: Resistor values question - by OldRestorer - 03-09-2015, 12:01 PM
RE: Resistor values question - by morzh - 03-09-2015, 12:47 PM
RE: Resistor values question - by OldRestorer - 03-19-2015, 10:03 AM
RE: Resistor values question - by Kestas - 03-19-2015, 11:41 AM
RE: Resistor values question - by OldRestorer - 03-19-2015, 01:10 PM
RE: Resistor values question - by OldRestorer - 03-19-2015, 02:55 PM
RE: Resistor values question - by Radioroslyn - 03-19-2015, 04:08 PM
RE: Resistor values question - by OldRestorer - 03-19-2015, 05:40 PM
RE: Resistor values question - by Radioroslyn - 03-19-2015, 06:06 PM
RE: Resistor values question - by OldRestorer - 03-19-2015, 07:40 PM
RE: Resistor values question - by Radioroslyn - 03-19-2015, 07:45 PM
RE: Resistor values question - by OldRestorer - 03-19-2015, 08:02 PM
RE: Resistor values question - by Radioroslyn - 03-19-2015, 09:54 PM
RE: Resistor values question - by Mondial - 03-19-2015, 11:09 PM
RE: Resistor values question - by OldRestorer - 03-20-2015, 12:59 PM
RE: Resistor values question - by OldRestorer - 03-20-2015, 01:13 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
My Philco 37-116 Restore
Are you measuring relative to the centertap or the GND?morzh — 11:57 PM
Philco 610B oscillator wiring
Still not clear on the wiring interface between the 6A7 and oscillator. After refering to the available schematics and s...Tubester — 07:18 PM
Refinishing Ideas
My 37-116 code 121 is the best sounding radio i have...a daily driver. Since we are talking about "changes". ...poulsbobill — 07:18 PM
My Philco 37-116 Restore
Hello, I finally got brave enough to take the cans off the Expander Unit. Got the grid cap wires replaced and back toget...dconant — 06:50 PM
Zenith H725
I got into the first AM IF can today, and found its mica was cracked. Amazing that it was still working. This one makes ...EdHolland — 06:10 PM
Philco model #20
AHH HA , I got it and can’t thank you fellows enough , when I changed the capacitors I took the advice and did not unsol...onlyrick — 02:24 PM
Zenith H725
Hello Ed, yes, I like letting projects run for few days to make sure they don't start acting up . Sincerely Richardradiorich — 01:03 PM
Philco 46-480 Electronic Restoration
I am almost finished with this restoration. All which remains is the power transformer. I cleaned it up some time ago, b...jrblasde — 12:41 PM
Philco model #20
I seem to recall in some TRF sets there being a Local/Distance toggle switch that removes the B+ from the first 24 rf tu...RodB — 09:46 AM
Refinishing Ideas
Hi Doppelganger, After rereading your thread, did you mount the Zenith speakers in the two bottom left and right pos...MrFixr55 — 09:39 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)