An Embarrassing Question!

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

An Embarrassing Question!

morzh
Odobenus rosmarus

Posts: 16,507
Threads: 572
Joined: Oct 2011
City: Jackson State, Province, Country: NJ

#11

07-29-2015, 02:26 PM

Sam,

Will you be shipping this as an assembled unit?
Remember, those J-bolts only were needed for shipping. They were removed upon delivery.
If you will be shipping it with the cabinet and the chassis being separated, you do not need those.
You can just (if you do not have it) drill a small hole where it is supposed to be, then drill the larger cylinder around it for the washer and use that small screw and a washer. You could test it and then supply them for the customer.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

An Embarrassing Question! - by Sam samuelian - 07-27-2015, 11:23 AM

RE: An Embarrassing Question! - by morzh - 07-27-2015, 03:10 PM

RE: An Embarrassing Question! - by Sam samuelian - 07-27-2015, 04:20 PM

RE: An Embarrassing Question! - by morzh - 07-27-2015, 04:59 PM

RE: An Embarrassing Question! - by Ron Ramirez - 07-27-2015, 07:40 PM

RE: An Embarrassing Question! - by morzh - 07-27-2015, 11:32 PM

RE: An Embarrassing Question! - by Ron Ramirez - 07-28-2015, 06:08 AM

RE: An Embarrassing Question! - by Sam samuelian - 07-28-2015, 11:38 AM

RE: An Embarrassing Question! - by Sam samuelian - 07-29-2015, 09:38 AM

RE: An Embarrassing Question! - by klondike98 - 07-29-2015, 10:54 AM

RE: An Embarrassing Question! - by morzh - 07-29-2015, 02:26 PM

RE: An Embarrassing Question! - by Sam samuelian - 08-18-2015, 01:05 AM

RE: An Embarrassing Question! - by sam - 08-18-2015, 03:40 AM

RE: An Embarrassing Question! - by morzh - 08-18-2015, 10:19 AM

RE: An Embarrassing Question! - by Arran - 08-23-2015, 12:53 AM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me