1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
An Embarrassing Question!
Arran
Phorum Expert
*****
Posts: 4,894
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA
#15

08-23-2015, 12:53 AM
 If the 1937 models are anything like the 1936 models, some had rubber shock mounts that were fitted into sockets on the inside front of the cabinet that would mate up with a pair of studs on the front apron of the chassis, so if it's like that then the one bolt at the rear is more then sufficient to keep the chassis in place. I believe that Renovated Radios sells reproductions of these mounts.
Regards
Arran
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
An Embarrassing Question! - by Sam samuelian - 07-27-2015, 11:23 AM
RE: An Embarrassing Question! - by morzh - 07-27-2015, 03:10 PM
RE: An Embarrassing Question! - by Sam samuelian - 07-27-2015, 04:20 PM
RE: An Embarrassing Question! - by morzh - 07-27-2015, 04:59 PM
RE: An Embarrassing Question! - by Ron Ramirez - 07-27-2015, 07:40 PM
RE: An Embarrassing Question! - by morzh - 07-27-2015, 11:32 PM
RE: An Embarrassing Question! - by Ron Ramirez - 07-28-2015, 06:08 AM
RE: An Embarrassing Question! - by Sam samuelian - 07-28-2015, 11:38 AM
RE: An Embarrassing Question! - by Sam samuelian - 07-29-2015, 09:38 AM
RE: An Embarrassing Question! - by klondike98 - 07-29-2015, 10:54 AM
RE: An Embarrassing Question! - by morzh - 07-29-2015, 02:26 PM
RE: An Embarrassing Question! - by Sam samuelian - 08-18-2015, 01:05 AM
RE: An Embarrassing Question! - by sam - 08-18-2015, 03:40 AM
RE: An Embarrassing Question! - by morzh - 08-18-2015, 10:19 AM
RE: An Embarrassing Question! - by Arran - 08-23-2015, 12:53 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
Thankyou for the kind words sir. I double checked it with my component tester and it read 2.7 ohms at .02mH.Stormlord5500 — 08:14 AM
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM

[-]
Who's Online
There are currently 719 online users. [Complete List]
» 1 Member(s) | 718 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios