Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 50-T702
#61

Yeah, the HV rectifier has been replaced. The HV is up where it should be about 5Kv. The picture is very viewable in a semi-dark room.

Crist
#62

Arran, that is interesting about the phosphor. I actually read about this recently in an old TV book. It mentioned that the phosphor can even degrade to the point that you can actually see into the tube from the front! Well, no matter if it is low emission or gas, the tube is tired. But, at least it is still giving service, and there is something to be said for that. Crist, that chassis is really looking nice! A little patience will pay off in locating a better tube. It took me over 30 years to find a NOS tube for one of my sets that I could afford. Mine had a line burned across the screen from a vertical sweep failure. That really wrecks an otherwise good picture! Icon_neutral

If I could find the place called "Somewhere", I could find "Anything" Icon_confused

Tim

Jesus cried out and said, "Whoever believes in me , believes not in me but in him who sent me" John 12:44
#63

(05-19-2016, 11:19 PM)Madmurdok Wrote:  Arran, that is interesting about the phosphor. I actually read about this recently in an old TV book. It mentioned that the phosphor can even degrade to the point that you can actually see into the tube from the front! Well, no matter if it is low emission or gas, the tube is tired. But, at least it is still giving service, and there is something to be said for that. Crist, that chassis is really looking nice! A little patience will pay off in locating a better tube. It took me over 30 years to find a NOS tube for one of my sets that I could afford. Mine had a line burned across the screen from a vertical sweep failure. That really wrecks an otherwise good picture! Icon_neutral

Yeah, I'm going to be patient.  Anybody have any knobs?

Crist
#64

 If you really can't stand watching a dim 7JP4 there are some scope tubes that will work as a cheap substitute, but the phosphors are P1 rather then P4, the drawback of course is that the phosphor is green rather then white. A lot of people go the scope tube route on one of those 3'' Pilot TVs since it's all too common to find one of the original 3KP4s with an open filament thanks to the goofy filament series string those sets used.
Regards
Arran
#65

Still looking for some knobs.

Crist




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 610B oscillator wiring
Thanks Terry. After checking my notes I think I recorded about -10v at the 6A7 G4/control grid. The screen grid (G3 &...Tubester — 05:59 PM
The list of my radio & TV collection!
Magical chords of forgotten melodies, old nostalgic music on an old radio... Saturday night blues on the Mid-Waves on an...RadioSvit — 12:20 PM
Philco 42-345 Restoration/Repair
Thank you MrFixr55 the issue with this radio is that the internal coil antenna is missing and there was a wire in its pl...osanders0311 — 11:34 AM
Philco 610B oscillator wiring
Regarding the oscillator circuit which is comprised of the 6A7's cathode, control grid, and screen grid. These elements ...Radioroslyn — 10:33 AM
Philco 42-345 Restoration/Repair
Hi OSanders, First off, welcome to the Philco Phorum where Phine Phamily-Phriendly Pholks Phull of Philco Phacts and P...MrFixr55 — 08:41 AM
Philco 42-345 Restoration/Repair
Today I've been reading through the site trying to learn more about this radio. I also soldered the lose power cord cabl...osanders0311 — 08:24 PM
Philco 610B oscillator wiring
Thanks David! I do have that same later prodution model 610 schematic. I've also studied the Philco service bulletins fo...Tubester — 08:12 PM
Philco 610B oscillator wiring
Some info from Beitmans says late production. David   David — 06:06 PM
Restoring Philco 96
Oh wow! Just found this thread.  Brings me back to early days on this phorum.  I did a 96 back in 2017.  Thread here: ...rfeenstra — 06:05 PM
Philco 610B oscillator wiring
Thanks for the replies. It's not the really the hum that I am after. Just trying to understand why only the shortwave ba...Tubester — 04:01 PM

[-]
Who's Online
There are currently 1987 online users. [Complete List]
» 3 Member(s) | 1984 Guest(s)
AvatarAvatarAvatar

>