Thread Rating:
  • 1 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 16B restoration
#76

Today the escutcheon came from Ed.
All I can say, I wouldn't be able to tell it from the original.
Top notch.
Too bad I come home late most days recently due to my resumed grappling practice which ends at about 9pm.
Saturday probably.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#77

Installed it, fits like a glove.

Kirk, thanks again for the screws.
I finished them with Testors gloss enamel, brown, that is sold in Hobby Lobby for $1.70 an ounce bottle.
I dipped them in it, cleared the groove with a toothpick and after drying 10 minutes put them in.

Need one more small rosette knob, will wait until Kutztown.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#78

This is the ecutcheon.

It is a bit off-color but Ed is not to be blamed; after all he only had my picture from the phone to look at.
I still think it came out great, especially the quality of the piece itself, it is pretty impeccable.

   
   

And the radio with it.

   
   

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#79

Beautiful job, Mike! Icon_clap Icon_thumbup

Greg V.
West Bend, WI
Member WARCI.org
#80

Mike

I don't see anything wrong with the color of that escutcheon. Ed did his usual great work. Icon_thumbup Icon_thumbup

And you'll be wanting a large rosette knob for that band switch.

Congratulations on another great restoration!

--
Ron Ramirez
Ferdinand IN
#81

Thanks! Yes need a large rosette knob. I guess the same size as the tuning knob?

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#82

Correct-a-mundo.

--
Ron Ramirez
Ferdinand IN




Users browsing this thread: 13 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 5713 online users. [Complete List]
» 2 Member(s) | 5711 Guest(s)
AvatarAvatar

>