Posts: 1,402
Threads: 70
Joined: Oct 2007
City: Linn Creek, MO
OK, back to Dan's original question. The Philco 20 is easy to work on. There is plenty of room under the chassis, easy to get to all parts. As with all the older Philcos, there are a few bakelite capacitor blocks. Plan on all the resistors being high in value. New dog bone resistors are available.  If there is a problem with the interstage transformer, there are new replacements. The speaker may be good, if not, they can be repaired or good ones show up eBay fairly often.
Steve
M R Radios C M Tubes
(This post was last modified: 03-15-2017, 09:28 AM by Steve Davis.)
Posts: 15,811
Threads: 553
Joined: Oct 2011
City: Jackson, NJ
Philco transformer is a stolid one, and Canadian (is it 20A for 25Hz?) if it is what I think should be an indestructible monster. 
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 1,402
Threads: 70
Joined: Oct 2007
City: Linn Creek, MO
By looking at the size of the transformer, it does not appear to be a 25 cycle radio. I have a 20A, the transformer core stack is almost twice as thick. Either way, the power transformer is very robust and not likely to ever fail.
Steve
M R Radios C M Tubes
Posts: 15,811
Threads: 553
Joined: Oct 2011
City: Jackson, NJ
You're right, looks like a regular 60 Hz job, still... Haven't seen Philco power transformers fail yet. They are a sturdy folk. Unlike their lesser cousins, the output and interstage, those are found bad all the time. Speaking of which, this one has both
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
(This post was last modified: 03-14-2017, 10:58 PM by morzh.)
Posts: 371
Threads: 103
Joined: Jul 2011
City: Calgary, AB, CA
I have recapped this radio and I had to change five resistors.
it now works fine, although the speaker is a little high pitched. Considering the age of the radio it sounds quite good.
I am replacing the broken parts on the grill.
when it gets warmer I will be doing the cabinet.
Dan in Calgary
Living in Calgary Alberta
Posts: 15,811
Threads: 553
Joined: Oct 2011
City: Jackson, NJ
Dan
High-pitched could be due to the stiff spider of the 20 speaker.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 371
Threads: 103
Joined: Jul 2011
City: Calgary, AB, CA
Yes I think you are right. I connected another speaker to the voice coil and it has more bass and sounds
like a regular speaker. This is fine the way it is, and I am not going to mess with it.
Dan in calgary
Living in Calgary Alberta
Users browsing this thread: 1 Guest(s)
|
|
Recent Posts
|
|
Shadow Meter Bulb
|
| Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM |
|
Philco 41-608 changer coupler
|
| 3D-printing...short of machining, of course.
Or molding.morzh — 05:20 PM |
|
Philco 41-608 changer coupler
|
| Thanks, Morzh.
That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM |
|
12' Philco
|
| If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel.
Kareem would have an e...morzh — 01:48 PM |
|
12' Philco
|
| And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM |
|
Hickok AC51 tube tester
|
| I think they have only shown the secondaries of the transformer.
Two of them feed the rectifiers' filaments.morzh — 12:58 PM |
|
IF can wire size and Rubber mounts?
|
| Arran
If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM |
|
12' Philco
|
| Rod,
Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently.
H...morzh — 12:54 PM |
|
Hickok AC51 tube tester
|
| Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM |
|
IF can wire size and Rubber mounts?
|
| Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM |
|
Who's Online
|
There are currently 6375 online users. [Complete List]
» 1 Member(s) | 6374 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
