Posts: 1,402
Threads: 70
Joined: Oct 2007
City: Linn Creek, MO
OK, back to Dan's original question. The Philco 20 is easy to work on. There is plenty of room under the chassis, easy to get to all parts. As with all the older Philcos, there are a few bakelite capacitor blocks. Plan on all the resistors being high in value. New dog bone resistors are available.  If there is a problem with the interstage transformer, there are new replacements. The speaker may be good, if not, they can be repaired or good ones show up eBay fairly often.
Steve
M R Radios C M Tubes
(This post was last modified: 03-15-2017, 09:28 AM by Steve Davis.)
Posts: 15,823
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
Philco transformer is a stolid one, and Canadian (is it 20A for 25Hz?) if it is what I think should be an indestructible monster. 
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 1,402
Threads: 70
Joined: Oct 2007
City: Linn Creek, MO
By looking at the size of the transformer, it does not appear to be a 25 cycle radio. I have a 20A, the transformer core stack is almost twice as thick. Either way, the power transformer is very robust and not likely to ever fail.
Steve
M R Radios C M Tubes
Posts: 15,823
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
You're right, looks like a regular 60 Hz job, still... Haven't seen Philco power transformers fail yet. They are a sturdy folk. Unlike their lesser cousins, the output and interstage, those are found bad all the time. Speaking of which, this one has both
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
(This post was last modified: 03-14-2017, 10:58 PM by morzh.)
Posts: 371
Threads: 103
Joined: Jul 2011
City: Calgary, AB, CA
I have recapped this radio and I had to change five resistors.
it now works fine, although the speaker is a little high pitched. Considering the age of the radio it sounds quite good.
I am replacing the broken parts on the grill.
when it gets warmer I will be doing the cabinet.
Dan in Calgary
Living in Calgary Alberta
Posts: 15,823
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
Dan
High-pitched could be due to the stiff spider of the 20 speaker.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 371
Threads: 103
Joined: Jul 2011
City: Calgary, AB, CA
Yes I think you are right. I connected another speaker to the voice coil and it has more bass and sounds
like a regular speaker. This is fine the way it is, and I am not going to mess with it.
Dan in calgary
Living in Calgary Alberta
Users browsing this thread: 1 Guest(s)
|
|
Recent Posts
|
|
Philco 38-7 Speaker
|
| 4-ohm speaker. Black, Green leads.tludka — 07:00 PM |
|
Philco 42-390, code 121 speaker
|
| #87 on the schematic.
This radio had a 8" Zenith speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM |
|
Philco 60 Squealing
|
| I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM |
|
Philco 38-7 Speaker
|
| Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM |
|
Philco 38-7 Speaker
|
| I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM |
|
Philco 42-390, code 121 speaker
|
| >>A closer examination of the very small print schematic indicates that the speaker is a PM type.
This shows a ...morzh — 05:18 PM |
|
Philco 60 Squealing
|
| Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM |
|
Philco 6K7
|
| The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND.
I am not ...morzh — 05:10 PM |
|
Philco 16B Parts
|
| Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM |
|
Philco 16B Parts
|
| Hi Dan,
Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM |
|
Who's Online
|
There are currently 3104 online users. [Complete List]
» 2 Member(s) | 3102 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
