Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

PHILCO 296 Model H Speaker Question
#1

Please forgive my ignorance in advance. I have picked up a Philco 296 which I am in the earliest stages of learning to restore. The first and most obvious problem is the speaker is trashed. The paper is gone and the center voice coil is trashed. The speaker is a Model H, but can it be replaced with another Model? I have learned that the Model H is a 3200 Ohm speak operating at 40ma.(I think...) Is there another Philco speaker that I can replace this one. I see a Model G on EBAY with the same plug, but I am not sure if this would work. I have much to learn. Any suggestions? Thank you for any help.

Frank
#2

Hi Frank and welcome,
Have a look here   http://philcoradio.com/phorum/showthread.php?tid=215  Find spk zip and click on it. There you will find specs for all of the Philco speakers. Looks like there are 4 or 5 that use the same cone/voice coil assembly including the G and H models.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

Welcome to the Phorum!
Icon_wave
#4

Thank you so much! I will go ahead and order the Model G and see where I am at. This will at least get me going. It may need to be re-coned and cleaned up, but perhaps this will at least get some sound.  The chassis is dirty but it looks like it has been recapped a long time ago and serviced several times over the years based upon on the dates and signatures. I have power to all the tubes so one step at a time. Thank you again and I may be back with several more questions.  Icon_wtf
#5

Thank you for having me. I am glad that I found this forum. I not afraid to learn, but I will admit that I am walking in the woods blind at this point. lol
#6

Have patience and you will be rewarded Icon_smile

Welcome.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#7

Terry and Mike will get you through it, have no fear. If you're an ace at reading schematics you're better off than I was a few months ago.

Greg

"We are here to laugh at the odds and live our lives so well that Death will tremble to take us."




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM

[-]
Who's Online
There are currently 5475 online users. [Complete List]
» 2 Member(s) | 5473 Guest(s)
AvatarAvatar

>