1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Enameled wire question.
Greenhorn
Member
***
Posts: 188
Threads: 21
Joined: Aug 2016
City: Adairsville, GA
#1

02-13-2018, 11:35 AM
Good Morning All,
Question 1: Will a lack of an enamel coating on coil wire affect the coil performance?
I'm working on a model 89..open tickler coil. When I un-wound the small coil I used lacquer thinner to try to clean the rotten, melted plastic left over on the Osc. coil...removing the enamel in the process. Icon_thumbdown

Question 2: Has there ever been a reported case of PTSD caused by attempting to restore a Model 89 that uses a 36 tube? Icon_confused
Thanks in advance.

Kelly
"He has all the virtues I dislike and none of the vices I admire." — Winston Churchill
Find
morzh
Odobenus rosmarus
*****
Posts: 15,818
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
#2

02-13-2018, 12:25 PM
Yes it will. If you wind it densely and it shorts out.
And if you do not wind it the same way it was, it might affect the inductance which may or may not be important.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Find
Greenhorn
Member
***
Posts: 188
Threads: 21
Joined: Aug 2016
City: Adairsville, GA
#3

02-13-2018, 11:20 PM
Thanks morzh.
"He has all the virtues I dislike and none of the vices I admire." — Winston Churchill
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration