Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Emerson 517 Moderne
#1

Well I had got 3 free radios a while back, one went to Terry, one is still in the box, this Emerson got done! The lighted dial pic is does not do justice, the cabinet came out OK, used Meguiars Wax and it came up good. I took the cabinet from a junker as the original had a big hole in top. 

It has been to the bench and it sounds quite nice, picks up my 250 Watt AM music station very well. So now I am wondering if I should give this to the guy who gave it to me, It was his Dad's.


https://www.flickr.com/photos/92577012@N...2698130911

What does ya think?

Paul

Tubetalk1
#2

Looks great!
Darn I thought you fixed the old cabinet!
Hear your going to be snow in pretty soon.
Got to get busy on that GE cabinet. I found
some small brads so I can nail the top back down.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

By the time I fixed the hole It would have cost me way more than the junk set, I needed a knob and I took the case. I still have a chassis that is not too bad though it has the small tubes instead of the Octal like the one we fixed. 

Paul

Tubetalk1
#4

Nice!

What's that big white console The Emerson was sitting on for the pictures?  Icon_wink

I don't hold with furniture that talks.
#5

I would give it back, lots of memories of his dad. David
#6

(03-14-2018, 11:21 AM)EdHolland Wrote:  Nice!

What's that big white console The Emerson was sitting on for the pictures?  Icon_wink



That is my Whirlpool console sounds good especially if change was left in your pocket. Icon_lol

Paul

Tubetalk1




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM

[-]
Who's Online
There are currently 3634 online users. [Complete List]
» 2 Member(s) | 3632 Guest(s)
AvatarAvatar

>