Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Question about A Philco 43-1201
#1

I was checking to see if anyone would know where to look for schematics or repair manual.
And what years it was made. Thank You.
#2

I'll be the first for once. Welcome to the phorum. You might want to recheck the model number and/or post a pic. No model by that number can be found. Might it be a 48-1201?

Pat
#3

Hi and welcome,
The "1201" was produced from 1946 thru 1948 aka the Bing Crosby set as he was the Philco pitch man in those days. It was pitched in a number of print ads and on his radio show. As for the set itself thru it's run there probably are some circuit differences like an eletrodynamic spkr vs a pm spkr or octal or loktal tubes but to the seasoned service tech of the day it presented little mystery .

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#4

Thank you for the information. I will look again the number was hard to see. It may help using the correct model number HAHA.
#5

Hello and welcome!
 I have restored a bunch of these. If you need help just let me know...

Kirk Icon_smile

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#6

I know it can't be but it looks like a 43-1201
It must be an 8 Thanks.
#7

We can identify it with a pic.
#8

   
#9

Actually, a pic of the radio itself would be more helpful.
#10

Sorry guys, that's 43-1201. No doubt a mis-stamp. 

Code dates on speaker, transformers, tuning cap etc will give an approx build date.

Tom
#11

The samp ends too sharply to have been a 8(especially at top & center), we'll just have to agree to disagree.

Maybe someone at Philco was pulling a prank?

Tom
#12

Thank you for all the help!
 It looks exactly like a 48-1201 so that's what I'm going with.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM
Philco 38-7 Speaker
7K should be fine. While not a perfect match (This transformer is meant for 6V6 tubes), Antique Electronic Supply (AES)...MrFixr55 — 08:03 AM
40-150 General questions
I discovered a stamp on the underside of the breadboard on my Philco 40-150. It is"56-1417' in black ink with numbe...Kevin_D — 07:14 AM
Philco 38-7 Speaker
FYI the Impedance of the HR20 (the one I have) secondary of the audio transformer is 5 ohms. The 38-7XX speaker is suppo...tludka — 04:22 PM
Philco 38-7 Speaker
Yeah, don't use the transformer currently on the H-20 (Dopf, I thought "H20, is that new technology, a speaker usin...MrFixr55 — 03:51 PM

[-]
Who's Online
There are currently 2733 online users. [Complete List]
» 2 Member(s) | 2731 Guest(s)
AvatarAvatar

>