1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
46-1201 Cabinet Covering
Bill Diesch
Junior Member
**
Posts: 3
Threads: 3
Joined: Jun 2018
City: Erie State, Province, Country: Colorado
#1

04-21-2019, 07:09 PM
Is there a source for the wood grain covering material used on the exterior of these sets? The one that I have really needs the covering replaced.
Find
klondike98
Phorum Moderator
******
Posts: 5,088
Threads: 270
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#2

04-21-2019, 09:50 PM
Welcome to the Phorum!
Icon_wave

The grain look on that model was what is known as a "Photo finish" which is a paper like finish with the grain applied to it.
Models with photo finish are listed in this thread: https://philcoradio.com/library/index.ph...otofinish/

There is a DIY tutorial for photo finishes here: https://philcoradio.com/schooley/
I've used those techniques but never on something with so many curved surfaces as the 1201. I'm sure others will have some thoughts.
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
OldRestorer
Electronic geneus
*****
Posts: 4,109
Threads: 310
Joined: Nov 2013
City: Kings Park NY
#3

04-22-2019, 06:42 AM
Hello Bill,
 Replacing the photofinish is fairly easy on these. I did a similar lamp radio a few years ago. All you need to do is find the veneer you want to use and print it on a good printer. Then just use adhesive and attach it. Last is to tone or clear as you would any radio. 

The most important thing is to find a proper veneer "photo". I used google to search for a nice walnut grain. 

Message me if you need any help. I have restored 4 or 5 of these 1201's so I know what you will need to get it done.

Kirk Icon_smile


Attached Files Image(s)
                   
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Find
« Next Oldest | Next Newest »




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
trying to identify this wire type
Thanks to all for the feedback. As Arran said, it is probably an older replacement and yes it has a grid cap so I will ...georgetownjohn — 09:32 PM
trying to identify this wire type
It's possible that the red wire, actually a grid cap lead, is a very old replacement, I can't remember seeing a pre 1939...Arran — 09:18 PM
Gilfillan Brothers Car Radio?
Hi everyone,  Special thanks to Joe Rossi for tracking down this obscure radio and thanks to others who took up the hun...Antipodal — 08:15 PM
trying to identify this wire type
Here's one source for your wire of many. Take care and BE HEALTHY! Gary P.S. Can't get the right color you need? I ...GarySP — 06:40 PM
trying to identify this wire type
...and modern wire of the appropriate gauges and insulation V-rating (300V minimum, usually shown right on the wire) is ...morzh — 05:47 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
I have a question about this radio, is there anyone that has access to this radio that has an intact unmolested speaker ...captainclock1988 — 04:28 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Well what makes me confuse all of those companies is that all three of those companies (Setchell-Carlson, Stromberg-Carl...captainclock1988 — 04:21 PM
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached.  I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration