1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 38-3 Reassembling the dial
Oscar Hernandez
Junior Member
**
Posts: 13
Threads: 7
Joined: Mar 2016
City: Laredo TX
#1

12-18-2020, 06:42 PM
Dear Friends
I have the dial completely disassembled, and need your help to put it back.
I have pics of 15 parts that would like to put together on the chassis as it was originally
I have attached a pic of a similar cabinet and a close up of the dial
Some parts I could figure out where they go, but the small parts are the ones I have no idea where they go
Thanks in advance for your help
P.S. Would like to hear something like, part x go along with part y in the back of part z, something like that. If any of our friends could share a process step by step of this work, it would be great
Unfortunately, I have no way to post all the 17 pics due to that I have reached the maximum allowed.


Attached Files Image(s)
                   
Find
klondike98
Phorum Moderator
******
Posts: 5,088
Threads: 270
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#2

12-18-2020, 07:16 PM
I don't have any personal experience with one of these but here's a link to a previous thread on a 38-3 dial that might be helpful.
https://philcoradio.com/phorum/archive/i...19180.html
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
klondike98
Phorum Moderator
******
Posts: 5,088
Threads: 270
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#3

12-18-2020, 10:16 PM
Also...you can also reply to your own post (with the "New Reply" button) and post additional pictures that way.
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
Oscar Hernandez
Junior Member
**
Posts: 13
Threads: 7
Joined: Mar 2016
City: Laredo TX
#4

12-20-2020, 09:57 PM
Dear Friends
It looks as if I finished reassembling the dial, but, there a loose piece that I coun't figured out where it belongs
If you have this info, please help to finish this project
Regards


Attached Files Image(s)
       
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM

[-]
Who's Online
There are currently 4733 online users. [Complete List]
» 3 Member(s) | 4730 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration