Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12, 2025) x

Thread Closed

41-680 bol changer
#1

Hello I’ve got a 41-680 with a beam of lite changer 4 wires are coming out of the tone 
Arm two come from the sensor to rca jack mounted on terminal strip along with two screw terminals one has black wire with spade lug theses go to the lite there’s no wire from radio to run the lite. I am wondering what voltage the lamp runs at is it filament voltage?
Lamp is good shows resistance.
Forrest.
#2

I think you mean a 41-608?
The lamp is powered from the bottom winding on #9.
You'll need a rf volt meter to measure it.

Part55-Philco 1941 RMS Year Book.pdf (philcoradio.com)

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got it!

Terry
#3

Hello Forrest,
welcome to the wild world of Philco's beam of Light  Icon_lol 
I also have a one in my collection too but my model is a single record player and loads through a slot like a car   cd player
#4

Hello,
Thank you terry for the reply yes it is a 41-608 sorry about that, yes I figured it out got the lamp lit and it lasted about 45 seconds and went out. I guess there no longer available I’m going to try building a rectifier off the filament supply to run a #47 bulb
Radiorich I’ve never heard of something like that how old is it?
#5

Might give a #55 lamp a try.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got it!

Terry




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
54C Complete Teardown/Rebuild
Hello Roy, here is this one sincerely Richardradiorich — 12:45 AM
54C Complete Teardown/Rebuild
Richard, Had grabbed it already but thank you just the same.  I find myself wanting to find some way to block out the...glyphmon — 12:03 AM
54C Complete Teardown/Rebuild
Hello roy, here is a link to the schematic . Sincerely Richardradiorich — 11:54 PM
54C Complete Teardown/Rebuild
Richard, The Silvertone 2014 also is a transformerless set, so I am incorporating a 1:1 600 ohm audio isolation transfo...glyphmon — 11:37 PM
Preliminary work on wife's Silvertone 2014
Did an alignment today which was interesting.  IF alignment went great, almost all was already spot-on.  Adjusting on th...glyphmon — 11:35 PM
54C Complete Teardown/Rebuild
The main problem with adding a Bluetooth input is that this set lacks a traditional power transformer to isolate it from...radiorich — 11:19 PM
54C Cabinet Refinish
I started stripping this cabinet before it got super chilly out because I knew I wasn't going to be able to work on ...glyphmon — 11:18 PM
54C Complete Teardown/Rebuild
While I'm waiting to wrap up the final steps on my wife's Silvertone 2014, I started disassembly on the next project.  O...glyphmon — 11:07 PM
Preliminary work on wife's Silvertone 2014
Hello roy, that great news glad it worked out for you !! Sincerely Richardradiorich — 10:50 PM
Preliminary work on wife's Silvertone 2014
Safety caps arrived today.  Soldered one in and had a successful first power-up.  No magic smoke escaped and it tunes in...glyphmon — 09:53 PM

[-]
Who's Online
There are currently 1352 online users. [Complete List]
» 1 Member(s) | 1351 Guest(s)
Avatar

>