1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 84 caps
Jimradio
Member
***
Posts: 194
Threads: 34
Joined: Jul 2016
City: Spring Lake MI
#1

01-03-2022, 01:07 PM
Restoring Philco 84 the Bakelite cap # 28 has 2 .015 caps, can I get by with .01Y or .05Y caps I don't have any .015 unless I order them.
Thanks.
Jim
Spring Lake MI
Find
morzh
Odobenus rosmarus
*****
Posts: 15,811
Threads: 553
Joined: Oct 2011
City: Jackson, NJ
#2

01-03-2022, 01:10 PM
If those are the AC input filters, yes, 0.01uF is what you need, Y-rated.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Find
Jimradio
Member
***
Posts: 194
Threads: 34
Joined: Jul 2016
City: Spring Lake MI
#3

01-03-2022, 05:44 PM
Thanks, Morzh
Jim
Spring Lake MI
Find
Jimradio
Member
***
Posts: 194
Threads: 34
Joined: Jul 2016
City: Spring Lake MI
#4

01-07-2022, 08:17 AM
Is there a later schematic not showing Cap. #32. I must have a later chassis it does not have cap. #32
Philco 84.
Thanks.
Jim
Spring Lake MI
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#5

01-07-2022, 11:31 AM
Just pretend it's not there. It's was to tune the field coil. What I do when I overhaul is replace 29 w/2x 10mfd@450v and 28 w/10mfd@35v. The 35v one goes w/the +side to the chassis and - to the hv c tap.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
(This post was last modified: 01-07-2022, 11:32 AM by Radioroslyn.)
Find
Jimradio
Member
***
Posts: 194
Threads: 34
Joined: Jul 2016
City: Spring Lake MI
#6

01-13-2022, 08:00 AM
This radio is now completed, very nice radio but a little different than others I have restored.
Jim
Spring Lake MI
Find
Jimradio
Member
***
Posts: 194
Threads: 34
Joined: Jul 2016
City: Spring Lake MI
#7

01-14-2022, 07:49 AM
    This is the completed radio pic.
Jim
Spring Lake MI
Find
Paul Philco322
Super Moderator
******
Posts: 4,381
Threads: 412
Joined: Jun 2011
City: Boston State, Province, Country: Massachusetts
#8

01-14-2022, 08:06 AM
Real nice jobIcon_smile.

Paul
Tubetalk1
Website Find
Radioroslyn
Phorum Expert
*****
Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#9

01-14-2022, 05:08 PM
Has a nice original patina.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
« Next Oldest | Next Newest »




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 6024 online users. [Complete List]
» 1 Member(s) | 6023 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration