Posts: 370
Threads: 102
Joined: Jul 2011
City: Calgary, AB, CA
Posts: 599
Threads: 24
Joined: Jan 2014
City: Edmonton AB CA
Dan, do you have a source for those 24 volt 30ma bulbs?
Gregb
Posts: 370
Threads: 102
Joined: Jul 2011
City: Calgary, AB, CA
I am going to check out my sources and see where I bought this one.
I have tried industrial electrical suppliers in the past.
The one I am thinking of did have 24 volt bulbs but I don't know the MA.. I will check into it and post here on the forum.. Dan
Posts: 370
Threads: 102
Joined: Jul 2011
City: Calgary, AB, CA
I did some research for those bulbs and I found a place called Bulb Town...www.bulbtown.com. I can get the bulbs and they cost $8.64 Canadian for 5 bulbs. I was going order 5 but the shipping came to over $30.00 so I did not order any..
I found the bulbs by looking under ''bulbs by volts ''at the bottom of that page.. The bulb was 24 volt,,,35MA. It has an E10 base[screw]
If you were to order $50.00 or more , the shipping is free.
I could not find anyplace in Calgary that had any..
Posts: 4,639
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
Try Mouser or WJOE radios, they seem to carry some obscure bulbs, I got some fuse lamps for my Marrantz from WJOE. One of the common faults these Deforest Crosley's have are the crumbling dial lamp leads, particularly on the one that rotate, that was a popular gimmick even on the later models, my 1938 Brahms model uses something similar even though the dial is rainbow shaped.
Regards
Arran
http://www.wjoe.com/all_lamps.htm
(This post was last modified: 06-24-2014, 03:13 PM by Arran.)
Posts: 370
Threads: 102
Joined: Jul 2011
City: Calgary, AB, CA
Posts: 1,400
Threads: 70
Joined: Oct 2007
City: Linn Creek, MO
That is a sharp looking radio 
Steve
M R Radios C M Tubes
Posts: 479
Threads: 73
Joined: Mar 2012
City: Riverside, CA
Looks absolutely beautiful, great job!!!
- Geoff
Posts: 15,444
Threads: 539
Joined: Oct 2011
City: Jackson, NJ
This is just majestic!
This dotted ornament around the dial, is it inlay or photo?
Posts: 370
Threads: 102
Joined: Jul 2011
City: Calgary, AB, CA
That inlay around the dial is actual wood inlay, the same as the inlay around the sides.
Posts: 1,455
Threads: 96
Joined: Jul 2012
City: Poughkeepsie, N.Y.
I just love it! Great job how does she play?
Posts: 370
Threads: 102
Joined: Jul 2011
City: Calgary, AB, CA
It plays just'''' alright.''''.. But when I turn the sensitivity control all the way to the right the volume goes right down. I just don't know enough about it to do any more so I plan on leaving it that way.
It does pick up all the stations and the tone and volume work fine.
Posts: 79
Threads: 13
Joined: Feb 2014
City: Bristol, RI
That's a beauty! Very sharp set. I'd have a hard time handing that one over for those windows..
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
Dan a nice job on an absolutely lovely radio. Congrats.
Jerry
A friend in need is a pest! Bill Slee ca 1970.
Users browsing this thread: 2 Guest(s)
|
|
Recent Posts
|
|
Cannot Adjust an IF Transformer’s cores
|
| It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM |
|
PT-6 antenna connections
|
| I seem to have lost my way on this PT-6.
I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM |
|
40-150 General questions
|
| Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM |
|
40-150 General questions
|
| I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM |
|
40-150 General questions
|
| It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM |
|
40-150 General questions
|
| Hi Kevin,
No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM |
|
Philco 38-7 Speaker
|
| 7K should be fine. While not a perfect match (This transformer is meant for 6V6 tubes), Antique Electronic Supply (AES)...MrFixr55 — 08:03 AM |
|
40-150 General questions
|
| I discovered a stamp on the underside of the breadboard on my Philco 40-150. It is"56-1417' in black ink with numbe...Kevin_D — 07:14 AM |
|
Philco 38-7 Speaker
|
| FYI the Impedance of the HR20 (the one I have) secondary of the audio transformer is 5 ohms. The 38-7XX speaker is suppo...tludka — 04:22 PM |
|
Philco 38-7 Speaker
|
| Yeah, don't use the transformer currently on the H-20 (Dopf, I thought "H20, is that new technology, a speaker usin...MrFixr55 — 03:51 PM |
|
Who's Online
|
There are currently 2761 online users. [Complete List]
» 2 Member(s) | 2759 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
