Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Remler wood console
#1

   

I found this on craigslist for $80. I can't seem to find any info on Remler wood consoles. I found lots of stuff about their table bakelite units. Anybody have any info about this? And maybe if it's a good buy?

Thanks,

Pat
#2

If it is clean inside...maybe. Provided the speaker is good.
#3

Looks like it might be an amputee though...

No matter where you go, there you are.
#4

It has a short.............................cabinet.

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
#5

(11-08-2014, 08:21 PM)Phlogiston Wrote:  It has a short.............................cabinet.

So do I. But I think I'll pass. Thanks to you all.
#6

  Given the weekend warrior refinish, the missing legs, broken escutcheon, broken speaker grille, mystery knobs, $80 is way to much, maybe $30-40 tops, if it had everything still in the back, but preferably less. As I keep explaining to people, it's the restoration costs in time and money that nails you, sometimes even if the radio is free it's too much.
Regards
Arran
#7

(11-09-2014, 02:11 AM)Arran Wrote:    Given the weekend warrior refinish, the missing legs, broken escutcheon, broken speaker grille, mystery knobs, $80 is way to much, maybe $30-40 tops, if it had everything still in the back, but preferably less. As I keep explaining to people, it's the restoration costs in time and money that nails you, sometimes even if the radio is free it's too much.
Regards
Arran

I agree 100%. My time isn't worth much because it's a hobby, and caps and resistors are cheap, but the rest can cost an arm and a leg, and you'll never be able to sell it for more than you have invested. I used to restore classic cars as a hobby, and if you weren't careful, you could put $25,000 into a car, and only sell it for $20,000. At least with this hobby, my bank account doesn't suffer as much, and my wife lets me sleep in the bedroom rather than the garage.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM
Philco 38-7 Speaker
7K should be fine. While not a perfect match (This transformer is meant for 6V6 tubes), Antique Electronic Supply (AES)...MrFixr55 — 08:03 AM
40-150 General questions
I discovered a stamp on the underside of the breadboard on my Philco 40-150. It is"56-1417' in black ink with numbe...Kevin_D — 07:14 AM
Philco 38-7 Speaker
FYI the Impedance of the HR20 (the one I have) secondary of the audio transformer is 5 ohms. The 38-7XX speaker is suppo...tludka — 04:22 PM
Philco 38-7 Speaker
Yeah, don't use the transformer currently on the H-20 (Dopf, I thought "H20, is that new technology, a speaker usin...MrFixr55 — 03:51 PM

[-]
Who's Online
There are currently 2593 online users. [Complete List]
» 1 Member(s) | 2592 Guest(s)
Avatar

>