Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Does anybody recognize this model
#1

Looking at buying this to restore but don't know what exactly Philco it is. Any guesses>


[Image: http://i87.photobucket.com/albums/k124/z...00x450.jpg]
#2

It could be 18. Used to be...
#3

Looks almost identical minus the brass pieces
#4

Gonna try for $35. I think if anything it would be a nice furniture piece once I refinish it. The wires have been cut from the unit.
#5

Could be also model 14HS

http://www.philcoradio.com/gallery/1933c.htm#c
#6

Its a 2 hour drive but think it might be worth it. Hopefully he sends me more photos of it tomorrow.
#7

If it is free.....
The Grill is missing. Whether or not the speaker is present is a good question too.
People could not give these away at Kutztown show....
#8

(12-02-2014, 10:34 PM)morzh Wrote:  If it is free.....
The Grill is missing. Whether or not the speaker is present is a good question too.
People could not give these away at Kutztown show....

I'm with Mike (Morzh) on this, find out if the speaker and other important bits are at least with it before making the trip, even then free may end up being too much for it. From the looks of that front panel someone was doing very stupid things to it, it doesn't just look like the grille was broken out but that someone went at it with a saw.
Regards
Arran
#9

I suppose the knobs and escutcheon are worth $35, but only to a person who needs them. This is a very needy parts set. I'm not sure where you're located, but I would hold off until a more complete unit shows up at a good price.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM

[-]
Who's Online
There are currently 4134 online users. [Complete List]
» 2 Member(s) | 4132 Guest(s)
AvatarAvatar

>