1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco model 19B I.F.
VE6ZRT
Junior Member
**
Posts: 5
Threads: 1
Joined: Feb 2015
City: Calgary, Alberta Canada
#1

02-28-2015, 04:36 PM
I have just restored a Philco chassis 319 ( Made in Canada version of 19/89 ) and am about to do an alignment on it.

I am confused since the I.F. frequency is indicated as 260KHz or 460KHz depending on what document you are using…

Can anyone provide a definitive answer on the I.F. frequency of the 319 chassis which was used in the model 19 series in Canada? I am going to guess 460KHz for now…it would be obvious I assume once I start the procedure…
Find
Ron Ramirez
Silent Key
*****
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana
#2

02-28-2015, 07:31 PM
Nope, the proper IF frequency for model 319 is the same as the USA model 19 - 260 kc.

(I checked the RCC data to be sure.)
--
Ron Ramirez
Ferdinand IN
Find
VE6ZRT
Junior Member
**
Posts: 5
Threads: 1
Joined: Feb 2015
City: Calgary, Alberta Canada
#3

03-02-2015, 09:22 AM
(02-28-2015, 07:31 PM)Ron Ramirez Wrote:  Nope, the proper IF frequency for model 319 is the same as the USA model 19 - 260 kc.

(I checked the RCC data to be sure.)

Thanks for the clarification Ron.  By the way this chassis works quite well even without an alignment...even the shadow meter still functions!  What I have also noticed is that the sound quality with the lowboy/console 10 inch speaker is quite good and there is basically no sign of 60/120HZ hum...very nice radio to listen to.

Thanks.

PH
Find
klondike98
Phorum Moderator
******
Posts: 5,129
Threads: 271
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#4

03-02-2015, 10:10 AM
Welcome to the Phorum!!!
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
VE6ZRT
Junior Member
**
Posts: 5
Threads: 1
Joined: Feb 2015
City: Calgary, Alberta Canada
#5

03-02-2015, 04:10 PM
(03-02-2015, 10:10 AM)klondike98 Wrote:  Welcome to the Phorum!!!

Thanks Bob...I have one more Philco to restore ( a floor model from 1939...)...might get to it in the fall...

PH
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
An attempt to remove the Field Coil from a G speaker
Mike; I've only run into a speaker with an open filed coil twice, and they were on newer speakers from the 1940s. One ...Arran — 12:48 AM
An attempt to remove the Field Coil from a G speaker
Arran Yes, this is my plan for now and what do I got to lose, this is not even the speaker from this radio, but one o...morzh — 10:44 PM
An attempt to remove the Field Coil from a G speaker
Mike;  I would unwrap the field coil, and see if maybe there a break near one of the ends, like where the coil wire att...Arran — 10:23 PM
An attempt to remove the Field Coil from a G speaker
...and this is what I did. I fed a little LT into the screwholes with a small brush, and a little on the rim next to the...morzh — 09:52 PM
Philco 40-120C Restoration
I combined the two 40-120C threads together as we like to keep the discussion of the same radio together. It helps with...klondike98 — 09:36 PM
Philco 40-120C Weak, Distorted Ouput
Just checked were I buy tubes price is four dollars. So living in Florid we have a local source for tubes. David    David — 09:14 PM
Philco 40-120C Weak, Distorted Ouput
The higher voltage may be due to higher mains voltage. My mains run 120-125AC when the set was new mains would be 110-11...David — 09:09 PM
Philco 40-120C Weak, Distorted Ouput
Thank you for your reply. I pulled a speaker from a Philco 41-221 and received the same result. I used a signal tracer t...bluecap — 08:45 PM
Philco 40-120C Weak, Distorted Ouput
Have you tried a different speaker? How did you trace the distortion? How do you know it is weak? What is the reference?...morzh — 08:33 PM
Philco 46-480 Electronic Restoration
Amen to that! Every time I think I’ve captured them all, I realize that there’s another error. My goal is to finish with...jrblasde — 07:00 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration