Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12, 2025) x

Thread Closed

42-1008P Stain *Cabinet Done*
#31

So here is what I am wondering about.


[Image: http://i1289.photobucket.com/albums/b519...edp7bu.jpg]

I believe the unit had original finish on it so from what I can see the trim piece that comes up along side the door is dark like other dark areas (red oval) and then hits a transition or swirl into that flat side piece (orange circle) and then the flat side (blue circle) is just about as toned as the face.

Does that seem to be what I should be going after?
#32

Just when you think you have a section looking good the sun hits it just right and you see a bad sanding job Icon_sad

Going to move on and figure out if I want to worry about fixing it.

I'm not all that good at this wood stuff.
#33

(03-28-2015, 01:16 PM)Edisla Wrote:  Just when you think you have a section looking good the sun hits it just right and you see a bad sanding job Icon_sad

Going to move on and figure out if I want to worry about fixing it.

I'm not all that good at this wood stuf
Edisla, don't give up. You have been working hard on it. Maybe just sand a little more with finer sand paper and it will look nice when covered with clear, etc. Icon_smile Don't forget to always sand WITH the grain.
#34

I wont give up.

I may give in a little but will not give up.
#35

Well here is how it came out.

Not exactly how I wanted it but it is close enough.

Before

[Image: http://i1289.photobucket.com/albums/b519...vxg1z2.jpg]

After
[Image: http://i1289.photobucket.com/albums/b519...cvak9q.jpg]
#36

Lookin Nice ...
#37

Yes it does look nice... Icon_thumbup Icon_thumbup
#38

looks fine to me great job Icon_clap Icon_thumbup
sam

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
54C Complete Teardown/Rebuild
Hello Roy, here is this one sincerely Richardradiorich — 12:45 AM
54C Complete Teardown/Rebuild
Richard, Had grabbed it already but thank you just the same.  I find myself wanting to find some way to block out the...glyphmon — 12:03 AM
54C Complete Teardown/Rebuild
Hello roy, here is a link to the schematic . Sincerely Richardradiorich — 11:54 PM
54C Complete Teardown/Rebuild
Richard, The Silvertone 2014 also is a transformerless set, so I am incorporating a 1:1 600 ohm audio isolation transfo...glyphmon — 11:37 PM
Preliminary work on wife's Silvertone 2014
Did an alignment today which was interesting.  IF alignment went great, almost all was already spot-on.  Adjusting on th...glyphmon — 11:35 PM
54C Complete Teardown/Rebuild
The main problem with adding a Bluetooth input is that this set lacks a traditional power transformer to isolate it from...radiorich — 11:19 PM
54C Cabinet Refinish
I started stripping this cabinet before it got super chilly out because I knew I wasn't going to be able to work on ...glyphmon — 11:18 PM
54C Complete Teardown/Rebuild
While I'm waiting to wrap up the final steps on my wife's Silvertone 2014, I started disassembly on the next project.  O...glyphmon — 11:07 PM
Preliminary work on wife's Silvertone 2014
Hello roy, that great news glad it worked out for you !! Sincerely Richardradiorich — 10:50 PM
Preliminary work on wife's Silvertone 2014
Safety caps arrived today.  Soldered one in and had a successful first power-up.  No magic smoke escaped and it tunes in...glyphmon — 09:53 PM

[-]
Who's Online
There are currently no members online.

>