Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Truetone 724 cabinet makeover
#16

The red on those dials really washes out over time. If I were going to keep the radio? I might let it slide for now. If you are going to sell then yeah I might replace dialscale..one less thing for a buyer to pick at.
Both places sell the replacements/radiolaguy and radiodaze.
I havent had to replace any yet for the model but in both places the coloring of their replacements looks off to my eyes.
Check with guys that have actually purchased replacements and see if that brown outer band is more accurate than the pictures suggest. The ones made for Detrola look right colorwise but the Truetones dont. Maybe a function of the photography/

http://www.radiodaze.com/truetone-d696-d724-727-3950/

http://www.radiodaze.com/detrola-model-1...m-ds-a677/
#17

(11-15-2015, 09:15 AM)JimZ Wrote:  The red on those dials really washes out over time.  If I were going to keep the radio?  I might let it slide for now.  If you are going to sell then yeah I might replace dialscale..one less thing for a buyer to pick at.
Both places sell the replacements/radiolaguy and radiodaze.
I havent had to replace any yet for the model but in both places the coloring of their replacements looks off to my eyes.
Check with guys that have actually purchased replacements and see if that brown outer band is more accurate than the pictures suggest.  The ones made for Detrola look right colorwise but the Truetones dont.  Maybe a function of the photography/

http://www.radiodaze.com/truetone-d696-d724-727-3950/

http://www.radiodaze.com/detrola-model-1...m-ds-a677/

Thanks for the tip, i like radio daze better , but will check around from others on accuracy
#18

I asked Paul Sanders Fred. He told me the one radiolaguy did is dead nuts to original..it was copied from one Paul sent along to him.




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM

[-]
Who's Online
There are currently 4192 online users. [Complete List]
» 1 Member(s) | 4191 Guest(s)
Avatar

>