Posts: 751
Threads: 91
Joined: Nov 2015
City: Jonesboro
State, Province, Country: AR
I have this 1929 Philco 95 Lowboy with a broken Grill. Can any of you wood/cabinet experts out there tell me what type of wood was originally used on this part of the broken grill  I'd like to make up a replacement using the same type of wood or veneer. Thanks! 
[Image: https://farm5.staticflickr.com/4117/3487...2c90_b.jpg]
Blessings,
Jeff W.
Jonesboro, Arkansas
http://jeffsradios.weebly.com
God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning
Posts: 765
Threads: 147
Joined: Aug 2012
City: Dallas, TX
Looks like walnut veneer over the thin layered plywood.
Posts: 4,861
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA
I think it was French walnut in particular, what cut doesn't matter. The grilles used in the 1928-29 "Lowboy" style console cabinets are almost as notorious for breakage as the Philco 20 cathedrals are. I think that the solution is to acquire some Baltic birch plywood of a suitable thickness, and then laminate it with some French walnut veneer, and then cut it out. Although if might be easier to check with Steve Davis about this, it's such a common problem that he may be replicating replacement grilles for these by now.
Regards
Arran
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
As I can recall - which might not be too good - these might be birch plywood without any other veneer. Using stain and toner to match the cabinet.
I think that later examples were sold without the grill at all.
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
I just looked at the one in our bathroom. The grain and color match the area of trim below the cut-out. So it is either walnut or mahogany. Just sand an area of the original. If it is pinkish or orange it is mahogany. If it is brown or reddish brown, walnut
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
Posts: 2,573
Threads: 337
Joined: Jun 2013
City: lawrenceville nj
Umm
you have a radio like that in your bathroom 
Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
yes. And it isn't in the bathtub.
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
Posts: 751
Threads: 91
Joined: Nov 2015
City: Jonesboro
State, Province, Country: AR
Thanks for your help guys.
phlogiston: do you use it to sing along to "Singing In The Bathtub" 
Blessings,
Jeff W.
Jonesboro, Arkansas
http://jeffsradios.weebly.com
God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning
Posts: 4,106
Threads: 310
Joined: Nov 2013
City: Kings Park NY
Is it so guests can put on music so no one can hear them ...... You know...
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
...careful...we have rules against "bathroom" humor...
Quote:I. Permitted and prohibited discussions.
A. The following types of discussions are not allowed in any part of the Phorum:
- Any personal attacks of one member upon another.
- Any libelous or potentially libelous postings.
- Any discussions of a lewd or pornographic nature.
- Any postings which may be considered as "spam".
- Any discussions of a political nature.
- Any references to bodily functions, or any type of "bathroom" humor.
Likewise, usernames that have anything to do with "bathroom" humor are not permitted and the user will be banned.
This is intended to be a family-friendly site.
--
Ron Ramirez
Ferdinand IN
Posts: 751
Threads: 91
Joined: Nov 2015
City: Jonesboro
State, Province, Country: AR
I'm off-season from my job, so I'm working on some projects I have been pushing to the back of the cue. I decided to make an attempt at making a new grill for this 1929 Philco 95 Lowboy.
I picked this up July 2016 at the Alameda California Historical Radio Society's annual swap meet and auction for $10.
This is the condition it was in when I brought it home. The radio is complete, and unbelievably has never been serviced.
[Image: https://farm5.staticflickr.com/4324/3503...a8d6_c.jpg]
Blessings,
Jeff W.
Jonesboro, Arkansas
http://jeffsradios.weebly.com
God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning
Posts: 751
Threads: 91
Joined: Nov 2015
City: Jonesboro
State, Province, Country: AR
I finally pulled the crushed grill piece out, and took it down to a store here in town that sells veneer. I asked the experts there what type of wood it was. The consensus was Mahogany that has Toner on it, possibly Walnut color.
[Image: https://farm5.staticflickr.com/4545/2492...1961_c.jpg]
Blessings,
Jeff W.
Jonesboro, Arkansas
http://jeffsradios.weebly.com
God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning
Posts: 751
Threads: 91
Joined: Nov 2015
City: Jonesboro
State, Province, Country: AR
I used Photoshop, a scan of the piece, and pics of another radio with the grill intact to create a template of the grill pattern, and printed it out.
[Image: https://farm5.staticflickr.com/4528/3876...dbe3_c.jpg]
I have had a good size sheet Mahogany on hand for quite some time left over from another repair, so I cut a piece off, and applied it to a small piece of nice plywood the correct thickness.
Using the printout, I rubbed some pencil on the back, then laid that down on the wood, traced it out, which transferred the design like carbon paper onto the wood, then used a fine tip sharpie to trace the pencil.
[Image: https://farm5.staticflickr.com/4581/3876...48cd_c.jpg]
[Image: https://farm5.staticflickr.com/4527/3876...548e_c.jpg]
The next step is to cut it out.
Blessings,
Jeff W.
Jonesboro, Arkansas
http://jeffsradios.weebly.com
God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning
Posts: 481
Threads: 18
Joined: Jan 2013
City: Mesa, AZ
WOW. I really like that model! Looks like your on the right track for the repair. I can't wait to see the phinished results!  What an excellent phind!
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
---another one of those threads that I lost.
Anyway, the model 95 in our bathroom:
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
Users browsing this thread:
|
|
Recent Posts
|
|
Need to purchase some accessories for restoration of my Old Philco Radio
|
| Here is a list of resources found in our online library that you might find useful. Mike's Gobs of Knobs email addres...klondike98 — 01:46 PM |
|
First Radio restoration
|
| Hi Tubeman,
Welcome to the Philco Phorum. Phamily Phriendly Pfun with Phine Pholks Phull of Philco Phacts. (See a p...MrFixr55 — 12:33 PM |
|
First Radio restoration
|
| You could post in the WANTED ADs section here on the Phorum and see if anyone has an RF generator that they want to sell...klondike98 — 11:55 AM |
|
Zenith H725
|
| Good ideas, thank you Arrange and Rich. I have the adhesive aluminum foil already and can try that immediately.
More ...EdHolland — 10:18 AM |
|
Graphics for majestic 1050 dial glass.
|
| Murf;
I found this thread on the ARF, the first photo has a pretty good view of the dial glass.
Regards
ArranArran — 01:12 AM |
|
Zenith H725
|
| hello Ed,
how about that speacial tape used for ducting it's like foil or how about thin piece of
aluminum roof flash...radiorich — 12:19 AM |
|
Zenith H725
|
| Ed;
One material that I have seen, but never tried for this was material for making exhaust gaskets, it's similar to ...Arran — 11:42 PM |
|
Zenith H725
|
| I just remembered, I have some hi temp silicone rubber material which could do the trick. Or a piece of FR4 laminate. Th...EdHolland — 08:39 PM |
|
Zenith H725
|
| The PSU filter cap arrived today (thank you USPS!) so I will work on that later.
Meanwhile, I have the dial, speaker...EdHolland — 06:42 PM |
|
Philco 610B oscillator wiring
|
| Thanks Terry. After checking my notes I think I recorded about -10v at the 6A7 G4/control grid. The screen grid (G3 &...Tubester — 05:59 PM |
|
Who's Online
|
| There are currently no members online. |
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
