Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Model 42-321 wavetrap
#1

The schematic for the Philco Model 42-321, shows a "condenser and choke assembly"; schematic no. 8; Philco part no. 76-1198.

On the radio I have, this part has been replaced with a capacitor only; no choke.

Does anyone have any info for this part? From the schematic, it looks like the capacitor value is .2 mf. No info on choke.
Is this meant to be a 455 HZ trap?

Any information on this part would be appreciated.

Thank you,

Don
#2

https://philcoradio.com/library/download...20Book.pdf
The .2 cap is the b- rail ground return to the chassis. The inductor is a choke to discourage longwave signals from interfering with the IF stage at 455KC.
Since we don't have much if any longwave signals these days the choke is unnecessary.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#3

Thanks, Terry

Don
#4

There are no more waves left to trap.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#5

Where I am there could be a use for the wave trap, there are a few beacons operating on longwave, I assume they are part of the LORAN system, or are related to a nearby airbase. There is one where you can sometimes hear a harmonic in the background of a station at 1040 Kc, though once that station was bought out and switched to a sports-gossip station I stopped listening to it, apparently it's a comedy station now. Anyhow reconstruting the choke is fairly easy, some sets used a proper coil form slipped over the cap, but with others they just wound some 18 or 20 gauge wire around the cardboard shell of the cap ten times, and called it done.
Regards
Arran




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached.  I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM

[-]
Who's Online
There are currently 4100 online users. [Complete List]
» 2 Member(s) | 4098 Guest(s)
AvatarAvatar

>