Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

marconi 157
#1

I picked a Marconi model 157 radio and when I got it the radio had a capacitor hum only so I recapped it and now I have a motor boating sound from half volume and up and no other sound only a low hum
#2

Assuming that all of the capacitors were installed correctly, check the values of all of the resistors in particular a canned-ohm if it has one.

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
#3

See if any tubes and their grid wires that are supposed to be encased in a shield are inside the shield.

Also: have you tested the tubes?

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#4

(11-19-2016, 10:51 AM)Phlogiston Wrote:  Assuming that all of the capacitors were installed correctly, check the values of all of the resistors in particular a canned-ohm if it has one.

I am not sure what a canned ohm resistor is but I will check the others
#5

(11-19-2016, 11:47 AM)morzh Wrote:  See if any tubes and their grid wires that are supposed to be encased in a shield are inside the shield.

Also: have you tested the tubes?
tubes have been tried in working radios and none of the tubes at all have shields
#6

(11-19-2016, 12:57 PM)the picker Wrote:  
(11-19-2016, 10:51 AM)Phlogiston Wrote:  Assuming that all of the capacitors were installed correctly, check the values of all of the resistors in particular a canned-ohm if it has one.

I am not sure what a canned ohm resistor is but I will check the others

It is the voltage divider resistor from which is derived the bias voltages. It is often a wire-wound in a metal sleeve riveted to the chassis for heat dissipation. The wire can burn open but most often the contacts become intermittent.

In most of my recent repairs, I would estimate that 1/2 to 2/3 of all resistors had either failed or were way out of tolerance.

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
#7

Here's schematic for anyone helping.
http://pacifictv.ca/schematics/marconi157data.pdf
#8

Russ might've meant Candohm.
It is a power resistor that is riveted to a chassis.


Ypi don't seem to have one.
Your neg bias seems to be made with a.... battery?
Is the battery good?

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#9

(11-19-2016, 02:25 PM)morzh Wrote:  Russ might've meant Candohm.
It is a power resistor that is riveted to a chassis.


Ypi don't seem to have one.
Your neg bias seems to be made with a.... battery?
Is the battery good?
are you talking about the 1.5 v bias cell if so yes I have it replaced
#10

candohm resister  looks like this
[Image: http://i117.photobucket.com/albums/o46/r...de8706.jpg]
could be smaller or larger with more tabs

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
#11

(11-19-2016, 03:21 PM)sam Wrote:  candohm resister  looks like this
[Image: http://i117.photobucket.com/albums/o46/r...de8706.jpg]
could be smaller or larger with more tabs

I will look but I do not think it has one
#12

I don`t think you have one

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
#13

(11-19-2016, 04:07 PM)sam Wrote:  I don`t think you have one
I looked and could not see one .
#14

Well, they look canned.

So never mind that, but check the voltages on the tubes starting with the 6F6.

Just curious too, does the eye tube do anything (signal indication)?

Do you have a signal tracer?

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
#15

For us US guys here's some pic's of it:   http://radioatticarchives.com/radio.htm?radio=12521

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Jackson 715 not working
Mrfixr55, its working now. I cleaned the switches and sockets with spray cleaner. Thanks for helping on this one.daveone23 — 06:26 PM
Jackson 715 not working
Now that you posted the schematic, I don't know why that Sprague electrolytic cap is across the meter, as it is not indi...MrFixr55 — 05:51 PM
HiFi (Chifi) tube amp build - but my own design.
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM
Jackson 715 not working
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM
Restoring Philco 37-604C
Yep. F5 is green, D5 is Red. Red is Bad. Green is Clean.morzh — 01:30 PM
Jackson 715 not working
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM
Restoring Philco 37-604C
(Insert Homer Simpson "DOPF" Here.) When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM
Philco 91 Speaker Replacement
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil. It wo...morzh — 08:44 AM
Philco 91 Speaker Replacement
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM
Philco 91 Speaker Replacement
As Rod said, it is OK to use a fitting speaker, and then look for an original one. If you buy a Hammond 125 output tr...morzh — 08:15 AM

[-]
Who's Online
There are currently 3900 online users. [Complete List]
» 1 Member(s) | 3899 Guest(s)
Avatar

>