Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

41-295/300 schematic
#1

Moderators. This post may be in the wrong forum or out of place. Please handle accordingly. 

My eyes aren't what they used to. As such I could not find a schematic for the 41-295/300 that I could actually read any of the values. So using the clarified schematic from Riders, and one out of the 1941 RMS Year Book. Using software available to me, I made the schematic so it was easier to read. At least for me. The software I was using isn't able to do the electrical symbols. So I pretty much left those alone. I deal with aircraft tech data for a living so I know everyone makes mistakes when writing these things. One area I wasn't able to clarify is the lower right hand corner for 13A - 13G

If some people wanted to take a look and see if or how many mistakes I made. I will gladly fix them, and then make available for everyone to use.

.pdf 41-300 INKED.pdf Size: 578.62 KB  Downloads: 239

.pdf Riders Vol 12 Clarified.pdf Size: 66.2 KB  Downloads: 175
#2

Hello afin. Have you looked in our library? Go to the bottom of the page and click on Philco Radio Library. The Philco 1941 RMS Yearbook has a much clearer schematic. You'll find it under Service Info. Hope this helps! Take care and BE HEALTHY! Gary

"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan
#3

Gary,

I have that schematic as well. Unfortunately, I was having trouble reading either one. Used both schematics, as well as the parts list, and the schematics for the individual modes selections to be able to clarify the schematic to make it more legible. 

There were a couple of portions I couldn’t read no matter which diagram I used. Such as the area in the lower right of the schematic by 13A thru 13G. 

Tom
#4

Hello,
What i believe you are having trouble reading on the schematic is the range that each of the individual automatic tuning buttons can be adjusted to for the 7 push buttons. This same information is stamped into the chassis in the same location as shown in the schematic. That information would be:

Between 13 A and 13 B (which would include 13 C) - 540 - 1030 KC
Between 13 D and 13 E - 650 - 1160 KC
Between 13 F and 13 G - 900 - 1600 KC

This information is in the 1941 Philco RMS yearbook on this site in the chapter titled - SETTING AND OPERATING ELECTRIC PUSH_BUTTON TUNING.
I hope that this information clears up the "not so clear" printing on the schematic.
Fran
#5

Thank you Fran,

Facepalm. When looking through the yearbook, guess I was more focused on my particular radio and missed that chapter. I haven't pulled the chassis out yet. Trying to get all of my ducks in a row before I do that. 

Corrected below.

Tom


Attached Files
.pptx 41-300 INKED.pptx Size: 503.15 KB  Downloads: 160




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Need Help to ID this radio 11 tube Philco
It is a 16B tombstone.morzh — 06:13 PM
Zenith H725
David - sorry, I reread your post and finally saw THD - now the % figures make sense. Thanks for explaining. The PSU...EdHolland — 06:06 PM
Need Help to ID this radio 11 tube Philco
Hi Everyone, New member but have been reading this for awhile for tips! Vaccum tubes were before my time so bear with ...Ken D. — 06:03 PM
My Philco 37-116 Restore
Thank you MrFixR55, I appreciate your comments very much. I do not detect much hum if any so I will be staying with the ...dconant — 05:15 PM
My Philco 37-116 Restore
Hi DConant Yes, you can replace chokes with resistors.  You do stand the risk of increased hum.  the solution is to inc...MrFixr55 — 04:23 PM
Zenith H725
1.7-3.9 %, a modified Sine wave inverter is around 25%. Most generators from big box stores run 10% at a 50% load. What ...David — 04:06 PM
My Philco 37-116 Restore
I am having a heck of a time doing the alignment on the AM band. I can't seem to dial in the 1500 KC oscillator. I can h...dconant — 03:35 PM
Zenith H725
David - I think I understand but what units are you discussing (Low of 1.7, high of 3.9)? Budget constraints for Ham ...EdHolland — 01:43 PM
My Philco 37-116 Restore
You're doing great. I wish I could be more involved, but my mind is right now preoccupied with the reason I am here in ...morzh — 12:21 PM
My Philco 37-116 Restore
Hope you guys are still with me. I have moved on to the alignment. I completed the IF alignment which was pretty muc...dconant — 10:47 AM

[-]
Who's Online
There are currently 742 online users. [Complete List]
» 2 Member(s) | 740 Guest(s)
AvatarAvatar

>