1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Thoughts on finish
Nathan Slingerland
Super Moderator
******
Posts: 1,887
Threads: 214
Joined: May 2015
City: Seattle State, Province, Country: WA
#19

06-07-2018, 01:28 PM
Lots of Gojo users here I suspect.

Here's an earlier thread discussing it: http://philcoradio.com/phorum/showthread.php?tid=13357
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Thoughts on finish - by oscartg - 06-06-2018, 11:54 AM
RE: Thoughts on finish - by Ron Ramirez - 06-06-2018, 12:35 PM
RE: Thoughts on finish - by oscartg - 06-06-2018, 12:40 PM
RE: Thoughts on finish - by John Bartley - 06-06-2018, 12:43 PM
RE: Thoughts on finish - by oscartg - 06-06-2018, 12:47 PM
RE: Thoughts on finish - by Ron Ramirez - 06-06-2018, 12:57 PM
RE: Thoughts on finish - by oscartg - 06-06-2018, 01:08 PM
RE: Thoughts on finish - by oscartg - 06-06-2018, 01:26 PM
RE: Thoughts on finish - by Ron Ramirez - 06-06-2018, 02:20 PM
RE: Thoughts on finish - by oscartg - 06-06-2018, 02:28 PM
RE: Thoughts on finish - by Ron Ramirez - 06-06-2018, 02:30 PM
RE: Thoughts on finish - by EdHolland - 06-06-2018, 04:01 PM
RE: Thoughts on finish - by Arran - 06-07-2018, 12:32 AM
RE: Thoughts on finish - by tbone - 06-07-2018, 06:20 AM
RE: Thoughts on finish - by John Bartley - 06-07-2018, 06:41 AM
RE: Thoughts on finish - by tbone - 06-07-2018, 06:47 AM
RE: Thoughts on finish - by EdHolland - 06-07-2018, 12:58 PM
RE: Thoughts on finish - by rdnzl - 06-07-2018, 01:21 PM
RE: Thoughts on finish - by Nathan Slingerland - 06-07-2018, 01:28 PM
RE: Thoughts on finish - by Phlogiston - 06-07-2018, 04:23 PM
RE: Thoughts on finish - by Arran - 06-07-2018, 10:00 PM
RE: Thoughts on finish - by oscartg - 06-12-2018, 11:12 AM
RE: Thoughts on finish - by Phlogiston - 06-12-2018, 02:53 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Zenith H725
IF2 will need replacement caps. The arcing was severe enough that the mica is pitted and holed where the HT flashed over...EdHolland — 04:04 PM
My Philco 37-116 Restore
Measuring from center tap like the tube voltages show. Cap 127 is isolated from ground. Cap 127 shown in upper left of p...dconant — 08:05 AM
My Philco 37-116 Restore
Are you measuring relative to the centertap or the GND?morzh — 11:57 PM
Philco 610B oscillator wiring
Still not clear on the wiring interface between the 6A7 and oscillator. After refering to the available schematics and s...Tubester — 07:18 PM
Refinishing Ideas
My 37-116 code 121 is the best sounding radio i have...a daily driver. Since we are talking about "changes". ...poulsbobill — 07:18 PM
My Philco 37-116 Restore
Hello, I finally got brave enough to take the cans off the Expander Unit. Got the grid cap wires replaced and back toget...dconant — 06:50 PM
Zenith H725
I got into the first AM IF can today, and found its mica was cracked. Amazing that it was still working. This one makes ...EdHolland — 06:10 PM
Philco model #20
AHH HA , I got it and can’t thank you fellows enough , when I changed the capacitors I took the advice and did not unsol...onlyrick — 02:24 PM
Zenith H725
Hello Ed, yes, I like letting projects run for few days to make sure they don't start acting up . Sincerely Richardradiorich — 01:03 PM
Philco 46-480 Electronic Restoration
I am almost finished with this restoration. All which remains is the power transformer. I cleaned it up some time ago, b...jrblasde — 12:41 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration